Make sure this part fits your vehicle

Toyota 47028-06030 Brake Master Cylinder Sub-Assembly W/Plate

2007-2008 Toyota 4702806030

Toyota 47028-06030 Brake Master Cylinder Sub-Assembly W/Plate
  • Part Description
    Cylinder Sub-Assy, Brake Master W/Plate
  • Part Name Code
    47028
  • Replaced By
    47201-06423
  • Manufacturer
    Toyota
Customer Questions & Answers
$172.00 MSRP: $244.52
You Save: $72.52 (30%)
1
ADD TO CART
Ships in 1-3 Business Days
  • Product Specifications

    BrandGenuine Toyota
    Part Name Code47028
    Manufacturer Part Number47028-06030
    Part DescriptionCylinder Sub-Assy, Brake Master W/Plate
    Item Dimensions10.1 x 7.7 x 5.4 inches
    Item Weight1.90 Pounds
    ConditionNew
    Fitment TypeDirect Replacement
    ManufacturerToyota
    SKU47028-06030
    WarrantyThis genuine Toyota part is guaranteed by Toyota's factory warranty.
    Shipping & ReturnShipping Policy Return Policy
    Warning: California’s Proposition 65
  • Vehicle Fitment

    Year Make Model Trim & Engine Important vehicle option details
    2007-2008 Toyota AvalonLimited, XL, XLS|6 Cyl 3.5L2GRFE; 2GRFE; GSX30L-AEAGKA, GSX30L-AEANKA, GSX30L-AEAPKA, GSX30L-AETGKA, GSX30L-AETNKA, GSX30L-AETPKA
    2007-2008 Toyota CamryLE, SE, XLE|4 Cyl 2.4L, 6 Cyl 3.5L2AZFE, 2GRFE; 2AZFE, 2GRFE; ACV40L-CEAGKA, ACV40L-CEANKA, ACV40L-CEASKA, GSV40L-CETGKA, GSV40L-CETNKA, GSV40L-CETSKA

Customer Questions & Answers

Q:
Is the above part number correct or is there another correct number for my car? Posted by ToyotaPartsDeal Specialist
A:
You can Select Your Vehicle to check if 47028-06030 fits your vehicle.
Posted by ToyotaPartsDeal Specialist
Q:
What should be done after the installation is complete for the 2013 Toyota Camry? Posted by Customer
A:
Thoroughly test the brake system before using the vehicle normally. Ensure the brake system functions properly and is free of any issues.
Posted by ToyotaPartsDeal Specialist
See expert answers on similar Brake Master Cylinder
Q:
What are the precautions and steps involved in removing, installing, and bleeding the master cylinder? Posted by Customer
A:
The Brake Master Cylinder allows the piston to pop out and be exposed. Hold the Brake Master Cylinder by the body and not the piston, or it may be damaged. Do not attempt to remove the piston or let it be scratched or damaged. For removal, first, take off the engine covers. Next, remove the windshield wiper assembly, followed by the cowl assembly. Depress the brake pedal several times to release the vacuum from the booster. Disconnect the electrical connector for the brake fluid level warning switch. Extract as much fluid as possible from the reservoir using a syringe. Place rags underneath the fittings and prepare caps or plastic bags for the line ends. Brake fluid damages paint. Take precautions to avoid spills. Loosen the fittings at the brake line ends where they connect to the Brake Master Cylinder using a flare-nut wrench. Detach the brake lines from the Brake Master Cylinder and plug the ends. Remove the nuts connecting the Brake Master Cylinder to the power booster. Carefully pull the Brake Master Cylinder off the studs, keeping it level to ensure the piston doesn't come out and avoid spilling the fluid. For installation, when setting up the Brake Master Cylinder, remove the piston and port protective caps. If the piston becomes dirty, clean it and evenly apply lithium soap-based glycol grease around the sliding portion. Place the Brake Master Cylinder over the power brake booster studs, tightening the nuts only to finger tight. Keep the Brake Master Cylinder level or with the piston end up to stop the piston from falling. Attach bleeder tubes to the Brake Master Cylinder's outlet ports, fill the reservoir with brake fluid, and slowly push down the brake pedal, expelling air into the reservoir. Repeat until no bubbles remain. Detach the bleed tubes and thread the brake line fittings into the Brake Master Cylinder. After ensuring finger-tightness, slightly adjust the fittings as needed. Tighten the mounting nuts and brake line fittings, refill the Brake Master Cylinder with fluid, and bleed the Brake Master Cylinder. To complete the installation, reverse the removal steps and test the brake system thoroughly before using the vehicle normally.
Posted by ToyotaPartsDeal Specialist
If you have any questions about this product, please don't hesitate to ask us. We will be happy to help you!

Genuine Toyota Part 47028-06030, the Right Choice

Your vehicle deserves only genuine OEM Toyota parts and accessories. To ensure reliability, purchase Toyota part # 47028-06030 Brake Master Cylinder Sub-Assembly W/Plate. It is sometimes referred to as Toyota Brake Master Cylinder, Toyota Master Cylinder Repair Kit. Our Toyota parts and accessories are expedited directly from authorized Toyota dealers strategically located all across the U.S. and are backed by the manufacturer's 12 month, 12,000 mile warranty. OEM Toyota parts are the best for restoring your vehicle to factory condition performance. This part fits 2007-2008 Toyota Avalon, 2007-2008 Toyota Camry.

Affordable, reliable and built to last, Toyota part # 4702806030 Brake Master Cylinder Sub-Assembly W/Plate stands out as the smart option. ToyotaPartsDeal.com is your prime online source with the biggest and best selection of genuine Toyota parts and accessories at giant discounted prices. We have the OEM Toyota parts and accessories you need at the wholesale prices. ToyotaPartsDeal.com has you covered no matter what type of Toyota vehicle you drive. For detailed Toyota parts information, click here.

Why choose Toyota Parts Deal

  • Dedicated Service

    Your complete satisfaction is our #1 goal

  • Lowest Prices

    Best deals on genuine OE parts from dealerships

  • Fast Delivery

    Orders are processed and delivered promptly