Genuine Toyota Solara Timing Belt

Toyota Solara Timing Belt Parts Questions & Answers

• Belt, Timing
  13568-29025
  Q: How do you remove the timing belt and Sprocket on V6 engine for 2002 through 2008 Toyota Solara and 2002 through 2006 Toyota Avalon?

  A: To remove the timing belt, start by disconnecting the negative cable from the battery and removing the coolant overflow tank and windshield washer tank. If applicable, remove the front suspension upper brace from the strut towers. Then, remove the drive belts from the alternator and power steering pump. Loosen the lug nuts on the right front wheel and raise the front of the vehicle, supporting it on jackstands. Remove the right front wheel and inner fender apron. Position the number one cylinder at TDC and support the engine with a jack. Remove the engine movement control rod and its bracket, as well as the spark plugs. Remove the upper timing belt cover and check for installation marks on the timing belt. Rotate the crankshaft pulley counterclockwise 60 degrees BTDC and remove the timing belt tensioner. Relieve tension between the camshaft sprockets and remove the timing belt from the sprockets. If necessary, remove the camshaft sprockets and the upper idler pulley. Remove the crankshaft pulley bolt and remove the pulley. Remove the lower timing belt cover and slip the timing belt guide off the crankshaft. If reusing the belt, check for a mark on the belt adjacent to the drilled mark on the crankshaft sprocket. Remove the no. 1 idler pulley and plate washer using an Allen wrench. If needed, remove the crankshaft sprocket. Finally, remove the lower sprocket retainer.
• Belt, Timing
  13568-09041
  Q: How to remove and install a timing belt and Sprocket on V6 engine for 1997 through 2001 Toyota Solara and 1997 through 2001 Toyota Avalon?

  A: Disconnect the battery and remove the coolant overflow, washer tanks, and front brace on Solara models. Remove belts from the alternator and power steering pump. Loosen lug nuts on the right front wheel, then raise the vehicle and remove the wheel, fender apron, and spark plugs. Set the number one cylinder at TDC and support the engine. Remove the engine movement control rod, upper timing belt cover, tensioner, and belt. Remove the lower cover, belt guide, and belt. For installation, clean the belt area and align the crankshaft sprocket keyway. Apply thread-lock to the lower idler pulley bolt, position the idler pulley, and install the belt. Attach the lower cover and fit the crankshaft pulley. Reinstall the upper idler pulley and front camshaft sprocket.
• Belt, Timing
  13568-09041
  Q: How to remove the timing belt and Sprocket on V4 engine for 1997 through 2001 Toyota Solara and 1997 through 2001 Toyota Avalon?

  A: To begin the removal process, start by disconnecting the negative battery cable and ensure the rear wheels are blocked while the parking brake is engaged. Loosen the lug nuts on the right front wheel, raise the vehicle, and securely support the front on jackstands. Proceed to remove the right front wheel and fender apron seal. Following this, remove the coolant overflow tank and the spark plugs and drive belts. Take out the alternator and its bracket and support the engine from beneath with a jack (using a wood block to avoid the oil pan drain plug). Remove the right Engine Mount and engine support rod. Afterward, remove the upper timing belt cover screws and pull up the wiring harness, then remove the upper (no.timing belt cover and gaskets. Ensure the number one piston is at TDC on the compression stroke and verify alignment between the small hole in the Camshaft pulley and the TDC mark on the cam bearing cap. Optionally, apply match marks on the sprocket and belt if reusing the timing belt. Loosen the upper (no.idler pulley set bolt and unhook the spring to slip the timing belt off the sprocket. If the camshaft sprocket requires removal, hold the rear camshaft with a wrench and remove the bolt. Remove the crankshaft pulley bolt, secure the engine from turning, and use a breaker bar and socket to loosen and remove the pulley. Proceed to remove the lower (no.timing belt cover and gaskets, slipping the belt guide off the crankshaft if needed. If reusing the timing belt, apply match marks on the sprocket and belt. Slip the timing belt off the sprocket and remove it. Inspect the idler pulleys for smooth operation and the spring for damage, and assess the belt for cracks, wear, or damage. Replace the timing belt with a new one if wear or damage is evident or if there are concerns. When installing the new belt, ensure the timing marks on the camshaft and crankshaft are correctly aligned. Reinstall idler pulleys and the tension spring, check timing mark alignment again, and fit the timing belt onto the appropriate components. Slip on the belt guide with the cupped side facing out and reinstall the lower timing belt cover and crankshaft pulley, verifying TDC marks. Place the timing belt over the camshaft sprocket while maintaining tension on one side, loosen the upper idler pulley bolt, and allow the spring to apply pressure. Slowly turn the crankshaft clockwise until the marks align correctly, then tighten the idler pulley. Rotate the crankshaft two revolutions and recheck the timing marks. If they align as required, reinstall the remaining components in reverse order, paying attention to gasket material on covers if necessary. Finally, run the engine to verify proper operation.