How to Remove and Install a Hood Cable and Hood Latch on a 2007-2015 Toyota Avalon?

For all Avalon cars, first remove the radiator mask. Then draw a line around the latch to guide alignment during re-installation. If your model has a plastic cover over the latch, you must take that off too. Use a socket wrench to stop the bolts that hold the hood latch to the radiator support. Open the latch by removing the hood cable hook that holds it in place. During installation, you must fine-tune the latch so the hood shuts tightly and make sure the bumpers on the hood press together slightly. Get the vehicle up, put jackstands under it for good support, and take off the front wheel. Take off the lower cover on the fender below and also the inner fender liner. Pull the hood cable loose from its latch assembly connection. Tie one end of a thin strand of wire to the cable, and remove all other clips keeping the cable at the fender and firewall. Open the driver's side door sill cover and kick panel, take off the driver's knee bolster panel, and disconnect the cable end from its release lever handle. Run the new cable and grommet toward the passenger area while holding on to the connecting line you put between the old and new cables, just make sure the new cable already has a grommet installed. After connecting the new cable to the piece of wire or string, push both back into the compartment until they end at the latch assembly location. Push the fresh cable into the hood cable grip, making sure the wire housing fits well into the lug on the handle frame. You put the grommet back into place by pushing from inside the car with your fingers.

Genuine Toyota Avalon Hood Cable

Hood Release Cable

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

19 Hood Cables found

View related parts
Toyota Avalon Hood Lock Control Cable Assembly
Part Number: 53630-AA030
$41.64 MSRP: $58.20
You Save: $16.56 (29%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Cable Assy, Hood Lock Control; Release Cable
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2005-2012 Toyota Avalon | Limited, XL, XLS | 6 Cyl 3.5L | 2GRFE; GSX30L-AEAGKA, GSX30L-AEANKA, GSX30L-AEAPKA, GSX30L-AETGKA, GSX30L-AETNKA, GSX30L-AETPKA
View related parts
Toyota Avalon Hood Lock Control Cable Assembly
Part Number: 53630-06150
$32.83 MSRP: $45.89
You Save: $13.06 (29%)
Ships in 1 Business Day
ADD TO CART
Product Specifications
- Other Name: Cable Assy, Hood Lock Control; Release Cable
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2013-2018 Toyota Avalon | Limited, XLE, XLE Premium, XLE Touring Or Touring | 4 Cyl 2.5L, 6 Cyl 3.5L | 2ARFXE, 2GRFE; AVX40L-AEXGBA, AVX40L-AEXPBA, GSX40L-AETGKA, GSX40L-AETPKA, GSX40L-AETQKA
View related parts
Toyota Avalon Hood Lever Sub-Assembly
Part Number: 53601-02040-C0
$47.59 MSRP: $66.52
You Save: $18.93 (29%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Lever Sub-Assembly, Hood; Lever, Release Handle, Release Lever
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2019-2022 Toyota Avalon | Limited, Touring, XLE, XSE | 4 Cyl 2.5L, 6 Cyl 3.5L | 2GRFKS, A25AFKS, A25AFXS; AXXA55L-AEZGBA, AXXA55L-AEZPBA, AXXH50L-AEXGBA, AXXH50L-AEXPBA, AXXH50L-AEXQBA, AXXH51L-AEXGBA, AXXH51L-AEXPBA, AXXH51L-AEXQBA, GSX50L-AEZGBA, GSX50L-AEZPBA, GSX50L-AEZQBA, GSX50L-AEZSBA
View related parts
Toyota Avalon Hood Lever Sub-Assembly
Part Number: 53601-02020-C0
$57.70 MSRP: $80.66
You Save: $22.96 (29%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Lever Sub-Assy, Hood Lock Control; Lever, Release Handle, Release Lever
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2013-2018 Toyota Avalon | Limited, XLE, XLE Premium, XLE Touring Or Touring | 4 Cyl 2.5L, 6 Cyl 3.5L | 2ARFXE, 2GRFE; AVX40L-AEXGBA, AVX40L-AEXPBA, GSX40L-AETGKA, GSX40L-AETPKA, GSX40L-AETQKA
View related parts
Toyota Avalon Hood Lever Sub-Assembly
Part Number: 53601-02020-C3
$43.78 MSRP: $61.19
You Save: $17.41 (29%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Lever Sub-Assembly, Hood; Lever, Release Handle, Release Lever
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2017-2020 Toyota Avalon | Limited, Touring, XLE, XLE Premium, XLE Touring Or Touring, XSE | 4 Cyl 2.5L, 6 Cyl 3.5L | 2ARFXE, 2GRFE, 2GRFKS, A25AFKS, A25AFXS; AVX40L-AEXGBA, AVX40L-AEXPBA, AXXA55L-AEZGBA, AXXA55L-AEZPBA, AXXH50L-AEXGBA, AXXH50L-AEXPBA, AXXH50L-AEXQBA, AXXH51L-AEXGBA, AXXH51L-AEXPBA, AXXH51L-AEXQBA, GSX40L-AETGKA, GSX40L-AETPKA, GSX40L-AETQKA, GSX50L-AEZGBA, GSX50L-AEZPBA, GSX50L-AEZQBA, GSX50L-AEZSBA
View related parts
Toyota Avalon Hood Release Cable
Part Number: 53630-06231
$34.14 MSRP: $47.72
You Save: $13.58 (29%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Cable Assembly, Hood Loc; Release Cable
- Replaces: 53630-33201
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2019-2022 Toyota Avalon | Limited, Touring, XLE, XSE | 4 Cyl 2.5L, 6 Cyl 3.5L | 2GRFKS, A25AFKS, A25AFXS; AXXA55L-AEZGBA, AXXA55L-AEZPBA, AXXH50L-AEXGBA, AXXH50L-AEXPBA, AXXH50L-AEXQBA, AXXH51L-AEXGBA, AXXH51L-AEXPBA, AXXH51L-AEXQBA, GSX50L-AEZGBA, GSX50L-AEZPBA, GSX50L-AEZQBA, GSX50L-AEZSBA
View related parts
Toyota Avalon Hood Lock Control Cable Assembly
Part Number: 53630-AC010
$39.00 MSRP: $54.51
You Save: $15.51 (29%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Cable Assy, Hood Lock Control; Release Cable
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 1995-1999 Toyota Avalon | XL, XLS | 6 Cyl 3.0L | 1MZFE; MCX10L-AEPGKA, MCX10L-AEPGKK, MCX10L-AEPNKA, MCX10L-AEPNKK, MCX10L-AESGKA, MCX10L-AESGKK, MCX10L-AESNKA, MCX10L-AESNKK
View related parts
Toyota Avalon Hood Lock Control Lever Sub-Assembly
Part Number: 53611-AA010-B1
$15.46 MSRP: $21.61
You Save: $6.15 (29%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Lever Sub-Assy, Hood Lock Control; Cable Handle, Release Handle
- Replaces: 53611-12040-B5
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2005-2011 Toyota Avalon | Limited, XL, XLS | 6 Cyl 3.5L | 2GRFE; GSX30L-AEAGKA, GSX30L-AEANKA, GSX30L-AEAPKA, GSX30L-AETGKA, GSX30L-AETNKA, GSX30L-AETPKA
View related parts
Toyota Avalon Hood Lock Control Lever Sub-Assembly
Part Number: 53611-AA010-B3
$15.46 MSRP: $21.61
You Save: $6.15 (29%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Lever Sub-Assy, Hood Lock Control; Cable Handle, Release Handle
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2005-2012 Toyota Avalon | Limited, XL, XLS | 6 Cyl 3.5L | 2GRFE; GSX30L-AEAGKA, GSX30L-AEANKA, GSX30L-AEAPKA, GSX30L-AETGKA, GSX30L-AETNKA, GSX30L-AETPKA
View related parts
Toyota Avalon Lever Sub-Assembly, Hood Lock Control
Part Number: 53611-AA010-C0
$13.67 MSRP: $19.11
You Save: $5.44 (29%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Lever Sub-Assy, Hood Lock Control; Cable Handle, Release Handle, Release Lever
- Manufacturer Note: BLACK,TRIM2#
- Replaces: 53611-12040-C0, 53611-12040-A0, 53611-12040-B3, 53611-12040-B7
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2010-2012 Toyota Avalon | Limited, XL, XLS | 6 Cyl 3.5L | 2GRFE; GSX30L-AETGKA, GSX30L-AETNKA, GSX30L-AETPKA
View related parts
Toyota Avalon Hood Lock Control Cable Assembly
Part Number: 53630-06230
$35.21 MSRP: $49.22
You Save: $14.01 (29%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Cable Assembly, Hood Loc; Release Cable
- Replaces: 53630-33200
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2019-2020 Toyota Avalon | Limited, Touring, XLE, XSE | 4 Cyl 2.5L, 6 Cyl 3.5L | 2GRFKS, A25AFKS, A25AFXS; AXXA55L-AEZGBA, AXXA55L-AEZPBA, AXXH50L-AEXGBA, AXXH50L-AEXPBA, AXXH50L-AEXQBA, AXXH51L-AEXGBA, AXXH51L-AEXPBA, AXXH51L-AEXQBA, GSX50L-AEZGBA, GSX50L-AEZPBA, GSX50L-AEZQBA, GSX50L-AEZSBA
View related parts
Toyota Avalon Hood Lock Control Lever Sub-Assembly
Part Number: 53611-AA010-A0
$13.67 MSRP: $19.11
You Save: $5.44 (29%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Lever Sub-Assy, Hood Lock Control; Cable Handle, Release Handle, Release Lever
- Manufacturer Note: IVORY,TRIM0#
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2005-2012 Toyota Avalon | Limited, XL, XLS | 6 Cyl 3.5L | 2GRFE; GSX30L-AEAGKA, GSX30L-AEANKA, GSX30L-AEAPKA, GSX30L-AETGKA, GSX30L-AETNKA, GSX30L-AETPKA
View related parts
Toyota Avalon Hood Lock Control Lever Sub-Assembly
Part Number: 53611-AA010-B4
$14.98 MSRP: $20.94
You Save: $5.96 (29%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Lever Sub-Assy, Hood Lock Control; Cable Handle
- Manufacturer Note: GRAY,TRIM16
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2005-2011 Toyota Avalon | Limited, XL, XLS | 6 Cyl 3.5L | 2GRFE; GSX30L-AEAGKA, GSX30L-AEANKA, GSX30L-AEAPKA, GSX30L-AETGKA, GSX30L-AETNKA, GSX30L-AETPKA
View related parts
Toyota Avalon Hood Lock Control Lever Sub-Assembly
Part Number: 53601-06020-A0
$42.08 MSRP: $58.81
You Save: $16.73 (29%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Lever Sub-Assy, Hood Lock Control; Release Lever
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 1997-1999 Toyota Avalon | XL, XLS | 6 Cyl 3.0L | 1MZFE; MCX10L-AEPGKA, MCX10L-AEPGKK, MCX10L-AEPNKA, MCX10L-AEPNKK, MCX10L-AESGKA, MCX10L-AESGKK, MCX10L-AESNKA, MCX10L-AESNKK
View related parts
Toyota Avalon Hood Lock Control Lever Sub-Assembly
Part Number: 53601-06020-E1
$42.48 MSRP: $59.39
You Save: $16.91 (29%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Lever Sub-Assy, Hood Lock Control; Release Lever
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 1995-1999 Toyota Avalon | XL, XLS | 6 Cyl 3.0L | 1MZFE; MCX10L-AEPGKA, MCX10L-AEPGKK, MCX10L-AEPNKA, MCX10L-AEPNKK, MCX10L-AESGKA, MCX10L-AESGKK, MCX10L-AESNKA, MCX10L-AESNKK
View related parts
Toyota Avalon Lever Sub-Assy, Hood Lock Control
Part Number: 53601-AA010-C0
Product Specifications
- Other Name: Cable Handle, Release Handle
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2000-2004 Toyota Avalon | XL, XLS | 6 Cyl 3.0L | 1MZFE; MCX20L-AEPGKA, MCX20L-AEPGKK, MCX20L-AEPNKA, MCX20L-AEPNKK, MCX20L-AESGKA, MCX20L-AESNKA
View related parts
Toyota Avalon Cable Assy, Hood Lock Control
Part Number: 53630-AC030
Product Specifications
- Other Name: Release Cable
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2000-2004 Toyota Avalon | XL, XLS | 6 Cyl 3.0L | 1MZFE; MCX20L-AEPGKA, MCX20L-AEPGKK, MCX20L-AEPNKA, MCX20L-AEPNKK, MCX20L-AESGKA, MCX20L-AESNKA
View related parts
Toyota Avalon Lever Sub-Assy, Hood Lock Control
Part Number: 53601-06020-C0
Product Specifications
- Other Name: Release Lever
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 1995-1999 Toyota Avalon | XL, XLS | 6 Cyl 3.0L | 1MZFE; MCX10L-AEPGKA, MCX10L-AEPGKK, MCX10L-AEPNKA, MCX10L-AEPNKK, MCX10L-AESGKA, MCX10L-AESGKK, MCX10L-AESNKA, MCX10L-AESNKK
View related parts
Toyota Avalon Lever Sub-Assy, Hood Lock Control
Part Number: 53601-06020-E2
Product Specifications
- Other Name: Release Lever
- Manufacturer Note: LT.ADOBE,TRIM42
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 1995-1998 Toyota Avalon | XL, XLS | 6 Cyl 3.0L | 1MZFE; MCX10L-AEPGKA, MCX10L-AEPGKK, MCX10L-AEPNKA, MCX10L-AEPNKK, MCX10L-AESGKA, MCX10L-AESGKK, MCX10L-AESNKA, MCX10L-AESNKK

Toyota Avalon Hood Cable

The front latch assembly and the interior hood release lever are connected via the Toyota Avalon Hood Cable. The lever is pulled to unhook the hood. The Hood Cable consists of a flexible metal wire housed in a protective outer covering that transmits the pulling force from the cabin handle to the latch, which does not require any electronics. The Toyota Avalon systems for many models have a primary Hood Cable that goes from the release handle to a junction beneath the hood where shorter secondary cables run from the junction to each latch, permitting the two latch points to disengage together. When the sheath is exposed to vibration, moisture, and temperature changes, the material can crack, allowing water to enter the Hood Cable. As a result, corrosion, stretching, and breakage can occur. Regular inspection of the Hood Cable is necessary as a worn-out one can cause the hood to be stuck in the latched position, making it inaccessible to the engine. Maintaining the Toyota Avalon mechanism in good condition ensures that the hood of the Toyota sedan opens and closes easily for the life of the car. This will help you in Avalon maintenance routines.

If you are in demand for superior quality and affordable OEM Toyota Avalon Hood Cable, then shop with us! We own a wide range of the reduced-priced genuine Toyota Avalon Hood Cable. You can purchase in confidence as all parts come with a manufacturer's warranty. Any issues with our products? No need to worry as we have a hassle-free return policy to guide you every step of the way.

Toyota Avalon Hood Cable Parts Questions & Experts Answers

Hood Lock Control Cable Assembly
53630-AA030
Q: How to Remove and Install a Hood Cable and Hood Latch on a 2007-2015 Toyota Avalon?
A:
For all Avalon cars, first remove the radiator mask. Then draw a line around the latch to guide alignment during re-installation. If your model has a plastic cover over the latch, you must take that off too. Use a socket wrench to stop the bolts that hold the hood latch to the radiator support. Open the latch by removing the hood cable hook that holds it in place. During installation, you must fine-tune the latch so the hood shuts tightly and make sure the bumpers on the hood press together slightly. Get the vehicle up, put jackstands under it for good support, and take off the front wheel. Take off the lower cover on the fender below and also the inner fender liner. Pull the hood cable loose from its latch assembly connection. Tie one end of a thin strand of wire to the cable, and remove all other clips keeping the cable at the fender and firewall. Open the driver's side door sill cover and kick panel, take off the driver's knee bolster panel, and disconnect the cable end from its release lever handle. Run the new cable and grommet toward the passenger area while holding on to the connecting line you put between the old and new cables, just make sure the new cable already has a grommet installed. After connecting the new cable to the piece of wire or string, push both back into the compartment until they end at the latch assembly location. Push the fresh cable into the hood cable grip, making sure the wire housing fits well into the lug on the handle frame. You put the grommet back into place by pushing from inside the car with your fingers.