Genuine Toyota Sequoia Drive Shaft

Toyota Sequoia Drive Shaft Parts Questions & Answers

• Shaft Assembly Propeller Front
  37140-0C110
  Q: How to remove and reinstall a driveshaft on a Toyota Tundra and Toyota Sequoia?

  A: Raise the vehicle and securely support it on jackstands. Place the transmission in Neutral with the parking brake off. Block the front wheels to prevent the vehicle from rolling. Using a scribe, a hammer and punch, or paint, make marks on the driveshaft and the Differential flange in line with each other. This is to make sure the driveshaft is reinstalled in the same position to preserve the balance. Remove the bolts securing the flange yoke to the rear differential. Turn the driveshaft as necessary to bring the bolts into the most accessible position. On vehicles with a two-piece driveshaft, remove the center bearing protector and remove the bolts, nuts, and washers from the center support bearing bracket. Lower the rear of the driveshaft. Slide the front of the driveshaft out of the transmission or transfer case or, if equipped with a companion flange, separate the flange at the transfer case. On 2WD models, wrap a plastic bag over the transmission extension housing and hold it in place with a rubber band. This will prevent loss of fluid and protect against contamination while the driveshaft is out. Remove the plastic bag from the transmission or transfer case and wipe the area clean. Inspect the oil seal carefully. Slide the front of the driveshaft into the transmission (2WD models) or bolt the U-joint flange yoke to the companion flange, installing the fasteners finger-tight (4WD models). Raise the center bearing (if equipped) into place and screw the retaining bolts in a few turns. Raise the rear of the driveshaft into position, checking to be sure the marks are in alignment. If not, turn the rear wheels to match the pinion flange and the driveshaft. Tighten all nuts. Remove the jackstands and lower the vehicle.
• Propelle Shaft Assembly
  37110-0C130
  Q: How to Properly Lubricating Various Components of a Drive Shaft and body on Toyota Tundra and Toyota Sequoia?

  A: To properly lubricate your vehicle, you will need a grease gun, clean rags, engine oil, chassis grease, lithium base grease, spray-on graphite or silicone lubricant. Begin by raising the vehicle with a jack and placing jackstands under the frame for easier access. Look under the vehicle for grease fittings on the driveshaft universal joints and slip yokes. Wipe the area around the grease fitting clean and force a little grease out of the nozzle to remove any dirt. Squeeze the trigger on the grease gun to force grease into the component until it oozes out of the bearing cup seals. Wipe off excess grease and repeat the procedure for the remaining fittings. Lubricate the driveshaft slip yoke by pumping grease into the fitting until it comes out of the slip yoke seal. Clean and lubricate the parking brake cable, cable guides, and levers with chassis grease. Lubricate the contact points on the steering knuckle stop with lithium base grease. Smear chassis grease on the hood latch mechanism and lubricate the cable at the latch. Lubricate all hinges with engine oil and the key lock cylinders with spray-on graphite or silicone lubricant. Finally, lubricate the door weather-stripping with silicone spray to reduce chafing and wear.
• Propelle Shaft Assembly
  37110-0C163
  Q: What Are the Maintenance Procedures for a Driveshaft and Universal Joint on Toyota Sequoia and Toyota Tundra?

  A: A driveshaft connects the transmission and Differential using universal joints. It's attached to the differential by a companion flange. 4WD models have a similar setup for the front driveshaft, while 2WD models use a splined yoke at the front. An oil seal prevents fluid leakage and dirt entry, which should be replaced if leakage is found. Two-piece driveshafts use center bearings for support. Regular lubrication and cleanliness are essential for the driveshaft.