How to remove and install the Ignition Lock Cylinder and Ignition Switch on a Toyota Sequoia?

Disconnect the cable from the negative terminal of the battery, then remove the left-side under-dash panel. Next, remove the headlight/turn signal switch and unplug the electrical connectors from the rear of the ignition switch. Disengage the two mounting clips and detach the switch from the lock cylinder housing, with installation being the reverse of removal. For the lock cylinder, use a small screwdriver to push the locking tabs outwards on the transponder key amplifier or the key light assembly, then slide the unit off the end of the key ignition lock cylinder housing. Insert the ignition key and turn it to the ACC position, then insert a small screwdriver into the hole in the bottom of the ignition switch casting and press the release button while pulling the lock cylinder straight out, with installation again being the reverse of removal.

Genuine Toyota Sequoia Ignition Switch

Starter Ignition Switch

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

4 Ignition Switches found

View related parts
Toyota Sequoia Ignition Or Starter Switch Assembly
Part Number: 84450-52010
$116.69 MSRP: $164.49
You Save: $47.80 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Switch Assy, Ignition Or Starter; Ignition Switch
- Replaces: 84450-BZ040
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2001-2007 Toyota Sequoia | Limited, SR5 | 8 Cyl 4.7L | 2UZFE; UCK35L-GKBLKA, UCK35L-GKBSKA, UCK35L-GKSLKA, UCK35L-GKSSKA, UCK45L-GKBLKA, UCK45L-GKBSKA, UCK45L-GKSLKA, UCK45L-GKSSKA
View related parts
Toyota Sequoia Ignition Or Starter Switch Assembly
Part Number: 84450-71010
$105.95 MSRP: $149.35
You Save: $43.40 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Switch Assy, Ignition Or Starter; Ignition Switch
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2008-2020 Toyota Sequoia | Limited, Platinum, SR5 | 8 Cyl 4.6L, 8 Cyl 4.7L, 8 Cyl 5.7L | 1URFE, 2UZFE, 3URFBE, 3URFE; UCK60L-GKALKA, UCK60L-GKASKA, UCK65L-GKALKA, UCK65L-GKASKA, UPK60L-GKTLKA, UPK60L-GKTSKA, UPK65L-GKTLKA, UPK65L-GKTSKA, USK60L-GKTLKA, USK60L-GKTSKA, USK60L-GKTZKA, USK65L-GKTLGA, USK65L-GKTLKA, USK65L-GKTSGA, USK65L-GKTSKA, USK65L-GKTZGA, USK65L-GKTZKA
View related parts
Toyota Sequoia Unlock Warning Switch Assembly
Part Number: 84052-33040
$34.50 MSRP: $48.22
You Save: $13.72 (29%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Switch Assy, Un-Lock Warning; Key Alarm Switch, Switch, Warning Switch
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2001-2007 Toyota Sequoia | Limited, SR5 | 8 Cyl 4.7L | 2UZFE; UCK35L-GKBLKA, UCK35L-GKBSKA, UCK35L-GKSLKA, UCK35L-GKSSKA, UCK45L-GKBLKA, UCK45L-GKBSKA, UCK45L-GKSLKA, UCK45L-GKSSKA
View related parts
Toyota Sequoia Unlock Warning Switch Assembly
Part Number: 84052-71010
$67.25 MSRP: $94.79
You Save: $27.54 (30%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Switch Assy, Un-Lock Warning
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2008-2020 Toyota Sequoia | Limited, Platinum, SR5 | 8 Cyl 4.6L, 8 Cyl 4.7L, 8 Cyl 5.7L | 1URFE, 2UZFE, 3URFBE, 3URFE; UCK60L-GKALKA, UCK60L-GKASKA, UCK65L-GKALKA, UCK65L-GKASKA, UPK60L-GKTLKA, UPK60L-GKTSKA, UPK65L-GKTLKA, UPK65L-GKTSKA, USK60L-GKTLKA, USK60L-GKTSKA, USK60L-GKTZKA, USK65L-GKTLGA, USK65L-GKTLKA, USK65L-GKTSGA, USK65L-GKTSKA, USK65L-GKTZGA, USK65L-GKTZKA

Toyota Sequoia Ignition Switch

The Toyota Sequoia Ignition Switch will start and control the electricity flowing to the engine of your Sequoia to be running by connecting the battery with the starter, ignition, fuel injection, and component circuits when the correct key is turned. In the lock position, the key can be removed, the steering shaft is locked, and gearshift movement from the park position is prevented to ensure theft protection. When the Ignition Switch is turned to acc, radio or power windows can be activated without the engine running. On maintains power to the engine and components once the vehicle is running. When the Ignition Switch is rotated to start, current flows to the starter motor which cranks and fires the engine. The key may jam or lose power if the tumblers or contacts inside the Ignition Switch become worn, causing the engine to stall or fail to crank. The Toyota Sequoia Ignition Switch keeps the right electrical path operational for daily operations of the Toyota Sequoia and the integrated security features of every Toyota Sequoia.

If you are in demand for superior quality and affordable OEM Toyota Sequoia Ignition Switch, then shop with us! We own a wide range of the reduced-priced genuine Toyota Sequoia Ignition Switch. You can purchase in confidence as all parts come with a manufacturer's warranty. Any issues with our products? No need to worry as we have a hassle-free return policy to guide you every step of the way.

Toyota Sequoia Ignition Switch Parts Questions & Experts Answers

Ignition Or Starter Switch Assembly
84450-71010
Q: How to remove and install the Ignition Lock Cylinder and Ignition Switch on a Toyota Sequoia?
A:
Disconnect the cable from the negative terminal of the battery, then remove the left-side under-dash panel. Next, remove the headlight/turn signal switch and unplug the electrical connectors from the rear of the ignition switch. Disengage the two mounting clips and detach the switch from the lock cylinder housing, with installation being the reverse of removal. For the lock cylinder, use a small screwdriver to push the locking tabs outwards on the transponder key amplifier or the key light assembly, then slide the unit off the end of the key ignition lock cylinder housing. Insert the ignition key and turn it to the ACC position, then insert a small screwdriver into the hole in the bottom of the ignition switch casting and press the release button while pulling the lock cylinder straight out, with installation again being the reverse of removal.