How to remove, install, and adjustment of the accelerator cable on Toyota Sienna?

This information is relevant only on the models up to year 2006, as from year 2007 the mechanism is an electrically operated throttle without the cable. To disconnect the accelerator cable first, pull it out from the negative terminal of the battery. Then, unscrew the locknut utilizing two wrenches on the threaded part of the accelerator cable which is located at the throttle body. Turn the throttle lever anticlockwise and push the accelerator cable end off the hole in the lever Next pull the end of the accelerator cable out of the accelerator pedal. Next, remove the cable and the casing out of the firewall to the engine compartment. For installation replace the steps with the following, making sure the grommet fits correctly in to the firewall. To retract the cable, there will always be some slack which need to be lifted and the adjusting screw will have to be turned till it is approximately 1/8 of an inch or 3 millimeters from the cable bracket. Secure the locknut and observe the cable bend on the throttle lever end and the housing casing should be 3/8 to 1/2 inch. If the deflection is not within given specifications, locknut has to be loosened in order to adjust the nut. After adjustment, check to be sure that the throttle valve opens wide when accelerator pedal is pushed to the floor and shuts when it is released, with the cable free of any stiff or rigid movement.

Genuine Toyota Sienna Accelerator Cable

Choke Cable

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

7 Accelerator Cables found

View related parts
Toyota Sienna Cable Assy, Accelerator Control
Part Number: 78180-08010
$103.12 MSRP: $145.36
You Save: $42.24 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Throttle Cable
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 1998-2003 Toyota Sienna | CE, LE | 6 Cyl 3.0L | 1MZFE; MCL10L-GFSDKA, MCL10L-GFSDKK, MCL10L-GFSGKA, MCL10L-GFSGKK, MCL10L-PFSDKA, MCL10L-PFSDKK, MCL10L-PFSGKA, MCL10L-PFSGKK, MCL10L-SESDKA, MCL10L-SESDKK
View related parts
Toyota Sienna Cable Assembly, Throttle
Part Number: 35520-45010
$99.93 MSRP: $140.87
You Save: $40.94 (30%)
Product Specifications
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 1998-2001 Toyota Sienna | CE, LE | 6 Cyl 3.0L | 1MZFE; MCL10L-GFSDKA, MCL10L-GFSDKK, MCL10L-GFSGKA, MCL10L-GFSGKK, MCL10L-PFSDKA, MCL10L-PFSDKK, MCL10L-PFSGKA, MCL10L-PFSGKK, MCL10L-SESDKA, MCL10L-SESDKK
View related parts
Toyota Sienna Cable Assembly, Throttle
Part Number: 35520-45020
$99.93 MSRP: $140.87
You Save: $40.94 (30%)
Product Specifications
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2000-2003 Toyota Sienna | CE, LE | 6 Cyl 3.0L | 1MZFE; MCL10L-GFSDKA, MCL10L-GFSDKK, MCL10L-GFSGKA, MCL10L-GFSGKK, MCL10L-PFSDKA, MCL10L-PFSDKK, MCL10L-PFSGKA, MCL10L-PFSGKK, MCL10L-SESDKA, MCL10L-SESDKK
View related parts
Toyota Sienna Cable Assy, Accelerator Control
Part Number: 78180-08020
Product Specifications
- Other Name: Throttle Cable
- Manufacturer Note: W(CRUISE CONTROL)
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 1998-2001 Toyota Sienna | CE, LE | 6 Cyl 3.0L | 1MZFE; MCL10L-GFSDKA, MCL10L-GFSDKK, MCL10L-GFSGKA, MCL10L-GFSGKK, MCL10L-PFSDKA, MCL10L-PFSDKK, MCL10L-PFSGKA, MCL10L-PFSGKK, MCL10L-SESDKA, MCL10L-SESDKK
View related parts
Toyota Sienna Cable Assy, Accelerator Auto Drive
Part Number: 78150-08010
Product Specifications
- Other Name: Cable
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 1998-2001 Toyota Sienna | CE, LE | 6 Cyl 3.0L | 1MZFE; MCL10L-GFSDKA, MCL10L-GFSDKK, MCL10L-GFSGKA, MCL10L-GFSGKK, MCL10L-PFSDKA, MCL10L-PFSDKK, MCL10L-PFSGKA, MCL10L-PFSGKK, MCL10L-SESDKA, MCL10L-SESDKK
View related parts
Toyota Sienna Cable Assy, Accelerator Auto Drive
Part Number: 78150-08020
Product Specifications
- Other Name: Cable
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2000-2003 Toyota Sienna | CE, LE | 6 Cyl 3.0L | 1MZFE; MCL10L-GFSDKA, MCL10L-GFSDKK, MCL10L-GFSGKA, MCL10L-GFSGKK, MCL10L-PFSDKA, MCL10L-PFSDKK, MCL10L-PFSGKA, MCL10L-PFSGKK, MCL10L-SESDKA, MCL10L-SESDKK
View related parts
Toyota Sienna Cable Assy, Accelerator Control
Part Number: 78180-08030
Product Specifications
- Other Name: Throttle Cable
- Manufacturer Note: W(CRUISE CONTROL)
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2000-2003 Toyota Sienna | CE, LE | 6 Cyl 3.0L | 1MZFE; MCL10L-GFSDKA, MCL10L-GFSDKK, MCL10L-GFSGKA, MCL10L-GFSGKK, MCL10L-PFSDKA, MCL10L-PFSDKK, MCL10L-PFSGKA, MCL10L-PFSGKK, MCL10L-SESDKA, MCL10L-SESDKK

Toyota Sienna Accelerator Cable

If you are in demand for superior quality and affordable OEM Toyota Sienna Accelerator Cable, then shop with us! We own a wide range of the reduced-priced genuine Toyota Sienna Accelerator Cable. You can purchase in confidence as all parts come with a manufacturer's warranty. Any issues with our products? No need to worry as we have a hassle-free return policy to guide you every step of the way.

Toyota Sienna Accelerator Cable Parts Questions & Experts Answers

Cable Assembly, Throttle
35520-45010
Q: How to remove, install, and adjustment of the accelerator cable on Toyota Sienna?
A:
This information is relevant only on the models up to year 2006, as from year 2007 the mechanism is an electrically operated throttle without the cable. To disconnect the accelerator cable first, pull it out from the negative terminal of the battery. Then, unscrew the locknut utilizing two wrenches on the threaded part of the accelerator cable which is located at the Throttle Body. Turn the throttle lever anticlockwise and push the accelerator cable end off the hole in the lever Next pull the end of the accelerator cable out of the accelerator pedal. Next, remove the cable and the casing out of the firewall to the engine compartment. For installation replace the steps with the following, making sure the grommet fits correctly in to the firewall. To retract the cable, there will always be some slack which need to be lifted and the adjusting screw will have to be turned till it is approximately 1/8 of an inch or 3 millimeters from the cable bracket. Secure the locknut and observe the cable bend on the throttle lever end and the housing casing should be 3/8 to 1/2 inch. If the deflection is not within given specifications, locknut has to be loosened in order to adjust the nut. After adjustment, check to be sure that the throttle valve opens wide when accelerator pedal is pushed to the floor and shuts when it is released, with the cable free of any stiff or rigid movement.