How to Remove, Inspect, and Install the Front Shock Absorber for the 2010 Toyota Prius?

For the wiper motor and link assembly to be pulled out, there is a cowl brace as well as the cowl top panel to be pulled out especially for 2010 and later models. Unscrew the wheel lug nuts, lift the automobile and put it on jack stands appropriately before pulling out the wheel. Loosen the brake hose bracket and then pull it away from the strut and disconnect the speed sensor harness by using the allen key to remove the clamp bracket bolt. Lose the nut on the stabilizer as this will fix the stabilizer bar and let it hang free. Note the orientation of the strut to the steering knuckle, and the locations of the bolts, as it may have been necessary to install special camber adjusting bolts. Shift the strut to knuckle nuts and knock out the bolts using hammer to punch them out. Very gently, pull the strut away from the steering knuckle, they are not to stress the inner CV joint or to allow the steering knuckle to fall out away from you. Secure the strut and spring assembly, then loosen the three strut-to-body nuts, but do not separate the center nut at this time; pull the assembly out of the fenderwell. Examine the strut body for such signs as fluid leakage, dents, cracks, and so on and examine the coil spring for such signs as chips, cracks in the coating, while examining the spring seat for cuts and deterioration. If any problems are identified, move on to the next step, which is, disassembling the strut. For installation, guide the strut assembly into the fenderwell, use the upper mounting studs to pass through the body holes and tighten the nuts in order to avoid dropping the strut. Engage the steering knuckle to the strut flange by sliding it in and install the bolts, ensure the match marks are correct and tighten the bolts. Join the brake hose bracket and speed sensor wiring harness bracket neatly as much as possible. Lastly, reintall the wheel and lug nuts, lower the vehicle and though the lug nuts, and finally tighten the upper mounting nuts before taking the car for a front-end alignment check and adjustment if required.

Genuine 2010 Toyota Prius Shock Absorber

Suspension Shock Absorber

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

11 Shock Absorbers found

View related parts
2010 Toyota Prius Shock Absorber Assembly Rear Left
Part Number: 48530-80533
$48.18 MSRP: $67.35
You Save: $19.17 (29%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Absorber Assembly, Shock, Rear Lh; Shock, Shock Absorber
- Position: Rear Driver Side
- Replaces: 48530-80534
- Item Weight: 6.50 Pounds
- Item Dimensions: 26.1 x 6.6 x 5.8 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 48530-80533
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2010 Toyota Prius Submodels:
- G, L, S | 4 Cyl 1.8L | 2ZRFXE; ZVW30L-AHXBBA, ZVW30L-AHXEBA, ZVW30L-AHXEBK, ZVW30L-AHXGBA
View related parts
2010 Toyota Prius Shock Absorber Assembly Front Right
Part Number: 48510-80542
$101.70 MSRP: $143.37
You Save: $41.67 (30%)
Ships in 1 Business Day
ADD TO CART
Product Specifications
- Other Name: Absorber Set, Shock ; Absorber Assembly, Shock, Front Rh; Strut
- Manufacturer Note: MARK 48510-47091,REFER TO ILLUST.
- Position: Front Passenger Side
- Replaces: 48510-80488
- Part Name Code: 48510
- Item Weight: 9.20 Pounds
- Item Dimensions: 26.9 x 8.3 x 7.5 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 48510-80542
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2010 Toyota Prius Submodels:
- G, L, S | 4 Cyl 1.8L | 2ZRFXE; ZVW30L-AHXBBA, ZVW30L-AHXEBA, ZVW30L-AHXEBK, ZVW30L-AHXGBA
View related parts
2010 Toyota Prius Shock Absorber Assembly Front Left
Part Number: 48520-80265
$100.52 MSRP: $141.71
You Save: $41.19 (30%)
Ships in 1 Business Day
ADD TO CART
Product Specifications
- Other Name: Absorber Set, Shock ; Absorber Assembly, Shock, Front Lh; Strut
- Manufacturer Note: MARK 48520-47091,REFER TO ILLUST.
- Position: Front Driver Side
- Replaces: 48520-80228
- Part Name Code: 48520
- Item Weight: 9.30 Pounds
- Item Dimensions: 27.1 x 8.2 x 7.6 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 48520-80265
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2010 Toyota Prius Submodels:
- G, L, S | 4 Cyl 1.8L | 2ZRFXE; ZVW30L-AHXBBA, ZVW30L-AHXEBA, ZVW30L-AHXEBK, ZVW30L-AHXGBA
View related parts
2010 Toyota Prius Shock Absorber Assembly Front Right
Part Number: 48510-80488
$101.70 MSRP: $143.37
You Save: $41.67 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Absorber Assembly, Shock, Front Rh
- Manufacturer Note: MARK 48510-47090,REFER TO ILLUST.
- Position: Front Passenger Side
- Replaced by: 48510-80542
- Part Name Code: 48510
- Item Weight: 9.40 Pounds
- Item Dimensions: 26.6 x 8.5 x 7.7 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 48510-80488
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2010 Toyota Prius Submodels:
- G, L, S | 4 Cyl 1.8L | 2ZRFXE; ZVW30L-AHXBBA, ZVW30L-AHXEBA, ZVW30L-AHXEBK, ZVW30L-AHXGBA
View related parts
2010 Toyota Prius Shock Absorber Assembly Front Left
Part Number: 48520-80228
$100.52 MSRP: $141.71
You Save: $41.19 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Absorber Assembly, Shock, Front Lh
- Manufacturer Note: MARK 48520-47090,REFER TO ILLUST.
- Position: Front Driver Side
- Replaced by: 48520-80265
- Part Name Code: 48520
- Item Weight: 9.90 Pounds
- Item Dimensions: 27.1 x 8.3 x 7.6 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 48520-80228
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2010 Toyota Prius Submodels:
- G, L, S | 4 Cyl 1.8L | 2ZRFXE; ZVW30L-AHXBBA, ZVW30L-AHXEBA, ZVW30L-AHXEBK, ZVW30L-AHXGBA
View related parts
2010 Toyota Prius Shock Absorber Assembly Rear Left
Part Number: 48530-80534
$48.18 MSRP: $67.35
You Save: $19.17 (29%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Absorber Assembly, Shock, Rear Lh; Shock Absorber
- Position: Rear Driver Side
- Replaced by: 48530-80533
- Item Weight: 6.60 Pounds
- Item Dimensions: 26.6 x 6.6 x 5.9 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 48530-80534
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2010 Toyota Prius Submodels:
- G, L, S | 4 Cyl 1.8L | 2ZRFXE; ZVW30L-AHXBBA, ZVW30L-AHXEBA, ZVW30L-AHXEBK, ZVW30L-AHXGBA
View related parts
2010 Toyota Prius Shock Absorber Assembly Front Left
Part Number: 48520-80230
$109.14 MSRP: $153.85
You Save: $44.71 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Absorber Assembly, Shock, Front Lh
- Position: Front Driver Side
- Part Name Code: 48520
- Item Weight: 9.30 Pounds
- Item Dimensions: 27.1 x 8.4 x 7.4 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 48520-80230
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2010 Toyota Prius Submodels:
- G, L, S | 4 Cyl 1.8L | 2ZRFXE; ZVW30L-AHXBBA, ZVW30L-AHXEBA, ZVW30L-AHXEBK, ZVW30L-AHXGBA
View related parts
2010 Toyota Prius Shock Absorber Assembly Front Right
Part Number: 48510-80490
$109.14 MSRP: $153.85
You Save: $44.71 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Absorber Assembly, Shock, Front Rh
- Position: Front Passenger Side
- Part Name Code: 48510
- Item Weight: 9.50 Pounds
- Item Dimensions: 26.4 x 8.5 x 7.6 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 48510-80490
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2010 Toyota Prius Submodels:
- G, L, S | 4 Cyl 1.8L | 2ZRFXE; ZVW30L-AHXBBA, ZVW30L-AHXEBA, ZVW30L-AHXEBK, ZVW30L-AHXGBA
View related parts
2010 Toyota Prius Shock Absorber Assembly Front Right
Part Number: 48510-80511
$113.91 MSRP: $160.56
You Save: $46.65 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Absorber Assembly, Shock, Front Rh
- Manufacturer Note: MARK 48510-47200
- Position: Front Passenger Side
- Part Name Code: 48510
- Item Weight: 9.90 Pounds
- Item Dimensions: 26.9 x 8.4 x 7.5 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 48510-80511
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2010 Toyota Prius Submodels:
- E | 4 Cyl 1.8L | 2ZRFXE; ZVW35L-BHXEBA, ZVW35L-BHXEBK
View related parts
2010 Toyota Prius Shock Absorber Assembly Front Left
Part Number: 48520-80242
$113.91 MSRP: $160.56
You Save: $46.65 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Absorber Assembly, Shock, Front Lh
- Manufacturer Note: MARK 48520-47200
- Position: Front Driver Side
- Part Name Code: 48520
- Item Weight: 9.60 Pounds
- Item Dimensions: 26.4 x 8.4 x 7.7 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 48520-80242
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2010 Toyota Prius Submodels:
- E | 4 Cyl 1.8L | 2ZRFXE; ZVW35L-BHXEBA, ZVW35L-BHXEBK
View related parts
2010 Toyota Prius Shock Absorber Assembly Rear Right
Part Number: 48530-80551
$42.74 MSRP: $59.75
You Save: $17.01 (29%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Absorber Assembly, Shock, Rear Rh
- Manufacturer Note: MARK 48530-47160
- Position: Rear Passenger Side
- Item Weight: 6.90 Pounds
- Item Dimensions: 26.9 x 6.8 x 5.8 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 48530-80551
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2010 Toyota Prius Submodels:
- E | 4 Cyl 1.8L | 2ZRFXE; ZVW35L-BHXEBA, ZVW35L-BHXEBK

2010 Toyota Prius Shock Absorber

With ToyotaPartsDeal.com, you have access to an extensive inventory of genuine 2010 Toyota Prius Shock Absorber, all priced competitively. Feel secure in your purchase, as all our OEM 2010 Toyota Prius Shock Absorber are covered by the manufacturer's warranty. Plus, we offer a hassle-free return policy and speedy delivery service.

2010 Toyota Prius Shock Absorber Parts Questions & Experts Answers

Q: How to Remove, Inspect, and Install the Front Shock Absorber for the 2010 Toyota Prius?
A: For the wiper motor and link assembly to be pulled out, there is a cowl brace as well as the cowl top panel to be pulled out especially for 2010 and later models. Unscrew the wheel lug nuts, lift the automobile and put it on jack stands appropriately before pulling out the wheel. Loosen the brake hose bracket and then pull it away from the strut and disconnect the speed sensor harness by using the allen key to remove the clamp bracket bolt. Lose the nut on the stabilizer as this will fix the stabilizer bar and let it hang free. Note the orientation of the strut to the steering knuckle, and the locations of the bolts, as it may have been necessary to install special camber adjusting bolts. Shift the strut to knuckle nuts and knock out the bolts using hammer to punch them out. Very gently, pull the strut away from the steering knuckle, they are not to stress the inner CV joint or to allow the steering knuckle to fall out away from you. Secure the strut and spring assembly, then loosen the three strut-to-body nuts, but do not separate the center nut at this time; pull the assembly out of the fenderwell. Examine the strut body for such signs as fluid leakage, dents, cracks, and so on and examine the coil spring for such signs as chips, cracks in the coating, while examining the spring seat for cuts and deterioration. If any problems are identified, move on to the next step, which is, disassembling the strut. For installation, guide the strut assembly into the fenderwell, use the upper mounting studs to pass through the body holes and tighten the nuts in order to avoid dropping the strut. Engage the steering knuckle to the strut flange by sliding it in and install the bolts, ensure the match marks are correct and tighten the bolts. Join the brake hose bracket and speed sensor wiring harness bracket neatly as much as possible. Lastly, reintall the wheel and lug nuts, lower the vehicle and though the lug nuts, and finally tighten the upper mounting nuts before taking the car for a front-end alignment check and adjustment if required.

Related 2010 Toyota Prius Parts

Alternate Year Models

2009 Toyota Prius Shock Absorber 2011 Toyota Prius Shock Absorber