My Garage
My Account
Cart
Genuine Toyota Celica Fuel Injector
Gas Injector- Select Vehicle by Model
- Select Vehicle by VIN
Select Vehicle by Model
orMake
Model
Year
Select Vehicle by VIN
For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).
35 Fuel Injectors found
Toyota Celica Fuel Injector Assembly
Part Number: 23209-74100$187.10 MSRP: $268.28You Save: $81.18 (31%)Ships in 1-3 Business Days
Toyota Celica Fuel Injector Assembly
Part Number: 23209-22040$174.57 MSRP: $250.32You Save: $75.75 (31%)Ships in 1-3 Business Days
Toyota Celica Fuel Injector Assembly
Part Number: 23209-74140$187.10 MSRP: $268.28You Save: $81.18 (31%)Ships in 1-3 Business Days
Toyota Celica Fuel Injector Assembly
Part Number: 23209-22060-01$181.64 MSRP: $260.47You Save: $78.83 (31%)Ships in 1-3 Business Days
Toyota Celica Fuel Injector Assembly
Part Number: 23250-41041$158.34 MSRP: $225.10You Save: $66.76 (30%)Ships in 1-3 Business DaysToyota Celica Fuel Injector
Part Number: 23250-45010$158.34 MSRP: $225.10You Save: $66.76 (30%)Ships in 1-3 Business Days
| Page 1 of 2 |Next >
1-20 of 35 Results
Toyota Celica Fuel Injector
The Toyota Celica Fuel Injector is manufactured to dispense the right amount of gasoline to the engine efficiently. This replaces the older carburetor system to achieve a balanced mixture. The injector is activated when the engine control unit sends an electrical signal that opens the nozzle so that the highly pressurized fuel can spray either directly into a combustion chamber or into the intake manifold, depending on the system layout. The mixture is created just as a piston moves down and draws in air into a cylinder. Each Fuel Injector of a Toyota Celica is part of a multi-point arrangement where one Fuel Injector is allocated to service each cylinder, which the control unit modulates the supply. Direct injection and indirect manifold injection are the two main injection methods. Both methods accurately measure and pressurize the fuel before release. The Toyota Celica makes use of a Fuel Injector per cylinder within a situation known as a "returnless" system, where the regulator is placed on the pump or control module to stop fueling lines. Though generally quite durable, the Toyota Celica Fuel Injector can develop clogs, internal leaks, or remain stuck open or closed. Any of those conditions may reduce engine performance or damage it.
If you are in demand for superior quality and affordable OEM Toyota Celica Fuel Injector, then shop with us! We own a wide range of the reduced-priced genuine Toyota Celica Fuel Injector. You can purchase in confidence as all parts come with a manufacturer's warranty. Any issues with our products? No need to worry as we have a hassle-free return policy to guide you every step of the way.
Toyota Celica Fuel Injector Parts Questions & Experts Answers
- Q: How to Check, Replace, and Install the Idle Control Valve, Throttle Body, Throttle Position Sensor, Fuel Pressure Regulator, Fuel Rail, and Fuel Injectors on Toyota Celica?A:To check the throttle body, ensure that the throttle linkage is moving freely, start the engine, disconnect each vacuum hose, and check the vacuum at every port with the engine idling and above the idle speed, then relate results with vacuum table available. For replacement, remove the cable from the negative terminal of battery, drain the radiator, if needed, then remove the hose clamps, air intake duct, accelerator cable from the throttle lever arm, throttle valve cable if coupled with an automatic transaxle, vacuum and coolant hoses label them, and disconnect the electrical connector for throttle position sensor, take out the mounting bolts of throttle body, disconnect and take off the throttle body with gasket, clean the To test TPS, disconnect the electrical connector, place a feeler gauge between the throttle stop screw and stop lever, test with an ohmmeter, if it cannot be adjusted within specifications then it has to be replaced. For the fuel pressure regulator, unscrew the fuel tank cap, disconnect the negative terminal of the battery cable, disconnect the vacuum line hose, put a container below the fuel return line, loosen the banjo bolt, unscrew the pressure regulator mounting bolts, and separate the regulator from the fuel rail but when reconnecting, ensure you replace the crush washers. For the cold start injector, disconnect the electrical connector, check the resistance between the two terminals of cold start injector and replace one if the resistance range is not well taken. The idle speed control valve involves starting the engine, inspecting the idle speed, shorting terminals to test and verifying the signals and replacing the control valve if faulty. For fuel rail and fuel injectors relieve fuel tank pressure, disconnect the negative terminal of the battery cable, disconnect accelerator cable, remove the electrical connector of cold start Injectors, disconnect the fuel line, remove the fuel rail mounting bolts, unbolt fuel rail/injector assembly, remove the fuel injected and replace the old ones with new injectors and seals using grommets and O-rings.
Related Toyota Celica Parts
Toyota Celica Fuel Filter
Toyota Celica Fuel Pump
Toyota Celica Fuel Filler Neck
Toyota Celica Fuel Pressure Regulator
Toyota Celica Fuel Door Release Cable
Toyota Celica Fuel Door
Toyota Celica Fuel Door Hinge
Toyota Celica Fuel Filler Hose
Toyota Celica Fuel Injector O-Ring
Toyota Celica Fuel Line Clamps
Toyota Celica Fuel Pump Gasket
Toyota Celica Fuel Pump Pulsator
Browse by Year
2005 Fuel Injector 2004 Fuel Injector 2003 Fuel Injector 2002 Fuel Injector 2001 Fuel Injector 2000 Fuel Injector 1999 Fuel Injector 1998 Fuel Injector 1997 Fuel Injector 1996 Fuel Injector 1995 Fuel Injector 1994 Fuel Injector 1993 Fuel Injector 1992 Fuel Injector 1991 Fuel Injector 1990 Fuel Injector 1989 Fuel Injector 1988 Fuel Injector 1987 Fuel Injector 1986 Fuel Injector 1985 Fuel Injector 1984 Fuel Injector 1983 Fuel Injector 1982 Fuel Injector 1981 Fuel Injector 1980 Fuel Injector 1979 Fuel Injector