How to remove and install the accumulator in a Toyota MR2?

Remove the spare tire and trim cover. Disconnect the two liquid line fittings from the accumulator. Cap the fittings immediately to prevent moisture from entering the system. Loosen the accumulator retaining strap screws and remove the accumulator. Installation is the reverse of removal, Be sure to tighten the liquid line fittings to the specified torque. If a new accumulator is being installed, add about 20 cc (0.7 oz)of compressor oil to the compressor.

Genuine Toyota MR2 A/C Accumulator

Accumulator

Enter your vehicle info to find more parts and verify fitment

Select Vehicle by VIN
Select Vehicle by Model

Select by VIN

Enter your VIN for the most accurate results.

Select by Model

-- Select Make --

-- Select Model --

-- Select Year --

3 A/C Accumulators found

View related parts
Toyota MR2 Tank, Receiver Air Conditioner
Part Number: 88471-20050
- Other Name: Dehydrator, Drier, Receiver
- Replaces: 88471-04020, 88471-06020
$54.92 MSRP: $76.77
You Save: $21.85 (29%)

Add to Cart
More Info
Fits the following Vehicles:
1993-1995 Toyota MR2 | 4 Cyl 2.0L, 4 Cyl 2.2L | 3SGTE, 5SFE; 3SGTE, 5SFE; SW20L-ACMZZA, SW20L-AJMZZA, SW21L-ACMZKA, SW21L-ACPZKA, SW21L-AJMZKA
Less Info
View related parts
Toyota MR2 Tank, Receiver Air Conditioner
Part Number: 88471-16040
- Replaced by: 88471-16050
$52.07 MSRP: $72.80
You Save: $20.73 (29%)
More Info
Fits the following Vehicles:
1990-1994 Toyota MR2 | 4 Cyl 2.0L, 4 Cyl 2.2L | 3SGTE, 5SFE; 3SGTE, 5SFE; SW20L-ACMZZA, SW20L-AJMZZA, SW21L-ACMZKA, SW21L-ACPZKA, SW21L-AJMZKA, SW21L-AJPZKA
Less Info
View related parts
Toyota MR2 Tank, Receiver Air Conditioner
Part Number: 88471-16010
- Other Name: Receiver & Dryer Assy, Cooler; Dehydrator, Drier
- Replaces: 88470-16010
More Info
Fits the following Vehicles:
1985-1989 Toyota MR2 | GT, Super Charger | 4 Cyl 1.6L | 4AGELC, 4AGZE; 4AGELC, 4AGZE; AW11L-WCMQFA, AW11L-WCMQFK, AW11L-WCPQFA, AW11L-WCPQFK, AW11L-WJMQFA, AW11L-WJMQFK, AW11L-WJMQRA, AW11L-WJMQRK, AW11L-WJPQFA, AW11L-WJPQRA
Less Info

Toyota MR2 A/C Accumulator Parts Questions & Answers

Tank, Receiver Air Conditioner
88471-16010
Q: How to remove and install the accumulator in a Toyota MR2?
A: Remove the spare tire and trim cover. Disconnect the two liquid line fittings from the accumulator. Cap the fittings immediately to prevent moisture from entering the system. Loosen the accumulator retaining strap screws and remove the accumulator. Installation is the reverse of removal, Be sure to tighten the liquid line fittings to the specified torque. If a new accumulator is being installed, add about 20 cc (0.7 oz)of compressor oil to the compressor.