How to Remove and Install the Neutral Safety Switch on a Toyota Sequoia?

The Park/Neutral Position (PNP) switch prevents the engine from starting in any gear other than Park or Neutral; if the engine starts in any other position, it may be out of adjustment or defective. Begin by raising the vehicle and securing it on jackstands. Remove the transmission control cable mounting nut from the shaft lever and detach the cable. Unplug the electrical connector from the PNP switch, then take off the shaft lever nut, washer, and lever. Use a screwdriver to bend back the locking tabs and remove the locknut, followed by the PNP switch retaining bolt to take out the switch. For installation, reverse the removal steps and check the switch, adjusting if necessary. To adjust, again raise the vehicle and secure it on jackstands, ensuring that on Sequoia models with rear height control suspension, the height control is set to NORMAL mode and turned OFF before raising the vehicle. Loosen the switch retaining bolt and position the switch in the N (neutral) position, aligning the groove with the neutral basic line, then tighten the switch retaining bolt while holding it in place.

Genuine Toyota Sequoia Neutral Safety Switch

Transmission Neutral Safety Switch

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

4 Neutral Safety Switches found

View related parts
Toyota Sequoia Neutral Start Switch Assembly
Part Number: 84540-04010
$134.19 MSRP: $190.77
You Save: $56.58 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Switch Assy, Neutral Start; Neutral Safety Switch, Range Sensor
- Manufacturer Note: (L)
- Replaces: 84540-71010
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2004-2007 Toyota Sequoia | Limited, SR5 | 8 Cyl 4.7L | 2UZFE; UCK35L-GKBLKA, UCK35L-GKBSKA, UCK35L-GKSLKA, UCK35L-GKSSKA, UCK45L-GKBLKA, UCK45L-GKBSKA, UCK45L-GKSLKA, UCK45L-GKSSKA
View related parts
Toyota Sequoia Neutral Start Switch Assembly
Part Number: 84540-0C010
$134.19 MSRP: $190.77
You Save: $56.58 (30%)
ADD TO CART
Product Specifications
- Other Name: Switch Assy, Neutral Start; Neutral Safety Switch, Range Sensor
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2008-2022 Toyota Sequoia | Limited, Platinum, SR5 | 8 Cyl 4.6L, 8 Cyl 4.7L, 8 Cyl 5.7L | 1URFE, 2UZFE, 3URFBE, 3URFE; UCK60L-GKALKA, UCK60L-GKASKA, UCK65L-GKALKA, UCK65L-GKASKA, UPK60L-GKTLKA, UPK60L-GKTSKA, UPK65L-GKTLKA, UPK65L-GKTSKA, USK60L-GKTLKA, USK60L-GKTSKA, USK60L-GKTZKA, USK65L-GKTLGA, USK65L-GKTLKA, USK65L-GKTSGA, USK65L-GKTSKA, USK65L-GKTZGA, USK65L-GKTZKA
View related parts
Toyota Sequoia Neutral Start Switch Assembly
Part Number: 84540-30320
$148.11 MSRP: $210.56
You Save: $62.45 (30%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Switch Assy, Neutral Start; Neutral Safety Switch
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2001-2005 Toyota Sequoia | Limited, SR5 | 8 Cyl 4.7L | 2UZFE; UCK35L-GKBLKA, UCK35L-GKBSKA, UCK35L-GKSLKA, UCK35L-GKSSKA, UCK45L-GKBLKA, UCK45L-GKBSKA, UCK45L-GKSLKA, UCK45L-GKSSKA
View related parts
Toyota Sequoia SWITCH ASSY, NEUTRAL
Part Number: 84540-0C020
$64.89 MSRP: $91.47
You Save: $26.58 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Neutral Safety Switch, Range Sensor
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2023-2025 Toyota Sequoia | 6 Cyl 3.5L | V35AFTS; VXKA70L-CRULZA, VXKA70L-CRUSZA, VXKA70L-PSULZA, VXKA70L-PSUSZA, VXKA70L-PSUZZA, VXKA71L-PRULZA, VXKA71L-PRUSZA, VXKA71L-PRUZZA, VXKA72L-CHUSZA, VXKA75L-CRULZA, VXKA75L-CRUSZA, VXKA75L-PSULZA, VXKA75L-PSUSZA, VXKA75L-PSUZZA, VXKA76L-PRULZA, VXKA76L-PRUSZA, VXKA76L-PRUZZA, VXKA77L-CHUSZA, VXKH70L-PSVLZA, VXKH70L-PSVZZA, VXKH71L-PRVLZA, VXKH71L-PRVZZA, VXKH75L-PSVLZA, VXKH75L-PSVUZA, VXKH75L-PSVZZA, VXKH76L-PRVLZA, VXKH76L-PRVZZA, VXKH80L-GKVLZA, VXKH80L-GKVSZA, VXKH80L-GKVZZA, VXKH85L-GKVLZA, VXKH85L-GKVSZA, VXKH85L-GKVZZA

Toyota Sequoia Neutral Safety Switch

The Toyota Sequoia Neutral Safety Switch stops the starter motor from operating unless the gear selector is in the park or neutral position to prevent the driver from starting the vehicle. Within the starting circuit is a small but essential component. It only completes the circuit when the transmission lever indicates it is in the proper position. When the lever is positioned in either drive or reverse, the Neutral Safety Switch protects the circuit by keeping it open, allowing the engine to remain silent to prevent the vehicle from lunging forward and causing damage to property or injury to people. The modern vehicles rely on one standard style of Neutral Safety Switch that performs this on-off task electronically through its internal contacts, and no alternate variants are noted for the Toyota or Sequoia line. Since no other versions are referenced, drivers can expect that any Neutral Safety Switch from any model year will behave the same. Therefore, the start button or key will only wake the engine when park or neutral is selected. By regularly being aware of this feature, Toyota owners can more quickly diagnose starting problems. After all, a worn Neutral Safety Switch may feel like a dead battery, but that may be confirmed by moving the shifter back into a valid slot in the cabin of a Sequoia.

If you are in demand for superior quality and affordable OEM Toyota Sequoia Neutral Safety Switch, then shop with us! We own a wide range of the reduced-priced genuine Toyota Sequoia Neutral Safety Switch. You can purchase in confidence as all parts come with a manufacturer's warranty. Any issues with our products? No need to worry as we have a hassle-free return policy to guide you every step of the way.

Toyota Sequoia Neutral Safety Switch Parts Questions & Experts Answers

Neutral Start Switch Assembly
84540-0C010
Q: How to Remove and Install the Neutral Safety Switch on a Toyota Sequoia?
A:
The Park/Neutral Position (PNP) switch prevents the engine from starting in any gear other than Park or Neutral; if the engine starts in any other position, it may be out of adjustment or defective. Begin by raising the vehicle and securing it on jackstands. Remove the transmission control cable mounting nut from the shaft lever and detach the cable. Unplug the electrical connector from the PNP switch, then take off the shaft lever nut, washer, and lever. Use a screwdriver to bend back the locking tabs and remove the locknut, followed by the PNP switch retaining bolt to take out the switch. For installation, reverse the removal steps and check the switch, adjusting if necessary. To adjust, again raise the vehicle and secure it on jackstands, ensuring that on Sequoia models with rear height control suspension, the height control is set to NORMAL mode and turned OFF before raising the vehicle. Loosen the switch retaining bolt and position the switch in the N (neutral) position, aligning the groove with the neutral basic line, then tighten the switch retaining bolt while holding it in place.