Toyota 90981-13046 Bulb

Various exterior lights are the parking/front sidemarker light bulbs which are installed in the outer, upper smaller recess area of the headlights; to replace, twist the socket of the bulb anti-clockwise and pull. Pull the bulb straight out to remove it from the socket and push it in until no further until to insert a new bulb. When you are screwed the new socket, position the arrow of the socket to the dot on the headlight housing. Front turn signal and fog light bulbs are-mount end on the bumper cover and since they're not enclosed they can be changed without having to lift the car. For the front turn signal bulb: rotary the socket as in the counter clockwise direction to unlock it from the vehicle's body, extract the bulb out, and introduce a new one into the until it becomes locked into its place. Before inserting the reference pins of the socket base, make sure that the lugs are properly aligned to the cutouts. Regarding the fog light bulbs, to change you have to pull the electrical connector, unscrew the socket using anticlockwise direction and then the steps are similar. To replace bulbs for the rear turn signal, brake/taillight, rear sidemarker, and back-up, there is a small door must be opened, the socket needs to be rotated in a counter clockwise direction then new bulb need to be installed by simply pushing the bulb straight in. License plate light bulbs can be replaced by first unscrewing the lens to reveal the light bulb which is then merely pulled straight out; the same applies conversely for installation. The center high-mounted brake light bulb calls for the lens to be popped off, followed by turning the socket in an anti-clockwise direction to uninstall it, and further following the bulb replacement process. For interior light bulbs like the dome lights, map lights, and door courtesy lights, remove the lens gently, unclip or REMOVE the old bulb and replace with a new one. If you have turn signal indicator bulbs, those require pulling the instrument cluster bezel using a flat-head screwdriver; the next step is twisting the socket in the counterclockwise direction to unlock it and further procedure is same to install it. Hazard flasher switch and power back window switch bulbs can be replaced by pulling the center trim panel, and then unscrewing the old bulb in a counterclockwise manner and make sure that the bulb is well screwed clockwise when a new one is put in its place. For heater and air conditioning control assembly bulbs, first, remove the assembly and then look for the bulb you want to replace and follow the same process followed when replacing the hazard flasher switch bulbs.

Note that 2018 and later Sequoia models and some 2018 and later Tundra models use LED headlights, which are not serviceable; if there is a problem with an LED headlight, the entire headlight assembly must be replaced. First, unplug the electrical connector from the headlight bulb holder for both low beam and high beam. Next, if equipped, pull the rubber watershield off the bulb assembly. Then, turn the bulb body counterclockwise and remove it from the housing. Finally, installation is the reverse of removal.

For fog lights, 2018 and later Sequoia and some Tundra models utilize LED fog lights that are not serviceable; if an issue arises, the entire assembly must be replaced. For halogen bulbs, disconnect the electrical connector, turn the bulb holder counterclockwise to remove it, and pull the bulb straight out for replacement, reversing the process for installation. For LED types, remove the bumper cover, take out the retaining clip, tape around the fog light cover's edge, and carefully pry up the cover to disengage clips before removing the fog light mounting bolts. Tundra models require removing a mounting screw and detaching the fog light from guides. Side marker and turn signal bulbs are located in the headlight housing; disconnect the electrical connector, turn the bulb holder counterclockwise to remove it, and pull the bulb straight out. For tail lights, Tundra models involve opening the tailgate, removing bolts, and rotating the housing for bulb access, while Sequoia models require opening the liftgate and removing screws to detach the housing. License plate lights on Tundra models involve removing screws for side-mounted lights or squeezing tabs for center-mounted lights, followed by turning the bulb holder counterclockwise to remove it. Sequoia models require removing retaining screws to detach the lens and pulling the bulb straight out. For high-mounted brake and cargo lights, remove screws to detach the lens for bulb access, pull out the defective bulb, and replace it. For dome lights, detach the lens and pull the bulb from the spring clips. Overhead personal light bulbs in Sequoia models require prying the lens out and pulling the bulb out for replacement. Installation for all components follows the reverse of removal.

The inner headlight bulbs are the high-beam bulbs and the outer bulbs are the low-beam bulbs.

When installing the new bulb, make sure that the three lugs on the mounting base of the bulb socket are aligned with their corresponding cutouts in the headlight housing. Then, insert the bulb socket into the housing and turn it clockwise until it stops.

Remove the instrument cluster and rotate the bulb counterclockwise to remove it.

Insert the bulb socket into the housing and turn it clockwise until it stops. The installation is otherwise the reverse of removal.

Reach behind the headlight assembly and rotate the bulb holder counterclockwise to remove the bulb.

Depress the release tab and pull off the connector.

Grasp the bulb holder securely and rotate it counterclockwise to remove it from the housing. This step also applies to the fog lamp bulb holder.

Open the hood. If you're replacing the right-side headlight, remove the windshield washer reservoir for access to the bulb. If you're removing the left-side headlight, remove the cover from the fuse/relay box for access to the bulb. If that doesn't give you enough working room, you can unbolt the fuse/relay box for more access. Otherwise, the headlight housing will have to be removed. Reach behind the headlight assembly and unplug the electrical connector by depressing the clip on the harness connector.

Carefully pry out the interior light housing from the trim panel.

Remove the rubber cover over the bulb, then release the spring securing the headlight bulb and remove the bulb.

If there is a problem with an LED headlight, the entire headlight assembly must be replaced.

1. Disconnect the electrical connector from the fog light bulb holder. 2. Turn the bulb holder counterclockwise and remove it from the housing. 3. Pull the bulb straight out to remove it from the bulb holder. 4. Installation is the reverse of removal.

high beam and low beam 90981 13046 65 watts 90981 ad001 55 wats

NO ONLY SOLD WITH HEADLAMP ASSY.

YES