Toyota 90981-11018 ASHTRAY RECEPTACLE Lamp Bulb

To replace the interior and map reading lights, carefully prise the light unit lens down at the side with a small screwdriver, then pull the festoon-type bulb from the sprung contacts. For models with map reading lights, hinge back the contact plate to remove the push-fit bulb, and fit the new bulb by reversing the removal process. If necessary, the light unit can be completely removed by taking out the two mounting screws and disconnecting the wiring plug. For the luggage compartment light, prise the light unit out from the trim panel, pull the festoon-type bulb from the contacts, and fit the new bulb by reversing the removal procedure. To address instrument panel illumination, remove the instrument panel, twist the relevant bulbholder anti-clockwise to remove it from the rear, and note that the bulbs may be one-piece items or have a wedge-base that can be pulled out before refitting the panel. The bulbs for switch illumination are integral with the switches and cannot be replaced separately. For heater control illumination, remove the heater control panel, twist the relevant bulbholder anti-clockwise using a screwdriver in the provided slot, and remove it from the rear, noting that the bulb is integral with the holder before refitting the panel.

To replace the front turn signal, remove the two Phillips screws and the lens, then turn the bulb counterclockwise about an eighth of a turn and pull it straight out, with installation being the reverse of removal. For the front side marker, take out the two screws securing the front inner fender panel to the outer fender, pull back the panel to access the side marker light bulb holder, grasp the bulb holder, turn it counterclockwise, and pull the bulb straight out; then rotate the bulb holder counterclockwise to remove it from the assembly and pull the bulb straight out, with installation reversing the removal steps. To change the dome light, pry off the plastic lens cover with a small screwdriver, remove the bulb from the assembly, and reinstall by reversing the steps. For the instrument panel, first remove the panel, then rotate the bulb holder counterclockwise and pull the bulb straight out, with installation being the reverse of removal. To access the rear side marker, open the rear luggage compartment lid, peel back the carpeting, and lift the particle board cover, then rotate the bulb holder counterclockwise to remove it from the assembly and pull the bulb straight out, with installation reversing the removal process. For the rear brake, turn signal, and backup lights, open the rear luggage compartment lid, push down on the two tabs on the top edge of the plastic tail light housing, pivot the assembly forward to access the burned-out bulb, remove it, and reinstall by reversing the steps.

To delete the turn signals and the fog lights, first you need to detach the radiator grille. For turn signal replacement, unscrew the lens retention screws, and gently pry the lens housing off the vehicle body, then twist the bushing of the bulb holder and remove it to change the bulb. Fog lights are as follows by unscrewing the retaining screws on the frame that are holding the housing to the vehicle and then pulling the housing out and unplugging the electrical connector from the back. For front side marker lights, unscrew the corresponding screws, then twist the lens and take it off; after that, insert a bulb and take it out. The rear side marker and rear turn signal lights can be replaced from the interior of the luggage compartment: the storage compartment cover should be dismantled and an inside panel should be gratuitously disconnected to expose the bulb holders. Twist the holder anti-clockwise to unlock it from the side marker assembly and then pull the bulb straight up. On the left side, localized behind the tool/jack storage compartment, that is accessible by removing the said compartment, there shall be the bulb holder. In the case of the dome light, take off the translucent plastic piece with an initiative of a screwdriver and pull the bulb out. They state that to delete an instrument panel bulb, the person has to use a screw-driver and unfasten the instrument cluster, then by rotating it anti-clockwise one has to pull the specific bulb carrier from the printed circuit board. One can open the liftgate to reach the rear combination light: there is a panel that covers the back side of the assembly, and it can be unplugged on a tab; the burnt out bulb will need to be removed and replaced. The location for the license plate light is as follows; first, strip off the covering panel to expose the bulb holder after that you rotate the bulb holder counterclockwise to provide clearance before pulling the bulb out. Removing the lights is the process of uninstalling them and, after that, check the luminosity of the acquired lights.

Reinstallation is the reverse of removal, including attaching the bulb to the terminals and securing the interior lens.

Remove the instrument cluster and rotate the bulb counterclockwise to remove it.

Reinstallation is the reverse of removal, including attaching the bulb to the terminals and securing the interior lens.