Toyota 35520-35190 Cable Assembly, Throttle

For 2003 and later model 3.4L V6 vehicles, it is important to note that they do not have a throttle valve cable. Instead, downshifts are controlled by an internal solenoid. Remove the shift solenoid valves from the valve body and the oil pipes. Remove the oil strainer if equipped, and then remove the valve body by removing the specified bolts. Lower the valve body and disengage the TV cable from the throttle cam. Insert the new cable through the hole in the case and secure it with the cable hold-down bolt. Connect the new TV cable to the cam and ensure that the groove of the manual valve is aligned with the pin of the lever before installing the valve body. Stake the cable stopper between 0.8 and 1.5 mm from the end of the cable sheath if the throttle cable being installed is new. Fill the transmission with new ATF and check the fluid level. Don't forget to check and adjust the TV cable if necessary.

Detach the cable from the negative terminal of the battery, ensuring you have the correct activation code for the anti-theft system if applicable. Loosen the locknut on the threaded portion of the throttle cable at the throttle body. Rotate the throttle lever and slip the throttle cable end out of the slot in the lever. Detach the throttle cable from the accelerator pedal and remove the two bolts securing the cable casing to the firewall. From inside the engine compartment, pull the cable through the firewall. For installation, reverse the removal steps, ensuring the cable casing grommet seats properly in the firewall. To adjust the cable, fully depress the accelerator pedal and check that the throttle is fully opened; if not, loosen the locknuts, depress the accelerator pedal, and adjust the cable until the throttle is fully open. Tighten the locknuts and recheck the adjustment, confirming that the throttle closes fully when the pedal is released.

For 2003 and later model 3.4L V6 vehicles, it is important to note that they do not have a throttle valve cable. Instead, downshifts are controlled by an internal solenoid. Remove the shift solenoid valves from the valve body and the oil pipes. Remove the oil strainer if equipped, and then remove the valve body by removing the specified bolts. Lower the valve body and disengage the TV cable from the throttle cam. Insert the new cable through the hole in the case and secure it with the cable hold-down bolt. Connect the new TV cable to the cam and ensure that the groove of the manual valve is aligned with the pin of the lever before installing the valve body. Stake the cable stopper between 0.8 and 1.5 mm from the end of the cable sheath if the throttle cable being installed is new. Fill the transmission with new ATF and check the fluid level. Don't forget to check and adjust the TV cable if necessary.

For 2003 and later model 3.4L V6 vehicles, it is important to note that they do not have a throttle valve cable. Instead, downshifts are controlled by an internal solenoid. Remove the shift solenoid valves from the valve body and the oil pipes. Remove the oil strainer if equipped, and then remove the valve body by removing the specified bolts. Lower the valve body and disengage the TV cable from the throttle cam. Insert the new cable through the hole in the case and secure it with the cable hold-down bolt. Connect the new TV cable to the cam and ensure that the groove of the manual valve is aligned with the pin of the lever before installing the valve body. Stake the cable stopper between 0.8 and 1.5 mm from the end of the cable sheath if the throttle cable being installed is new. Fill the transmission with new ATF and check the fluid level. Don't forget to check and adjust the TV cable if necessary.

Detach the cable from the negative terminal of the battery, ensuring you have the correct activation code for the anti-theft system if applicable. Loosen the locknut on the threaded portion of the throttle cable at the throttle body. Rotate the throttle lever and slip the throttle cable end out of the slot in the lever. Detach the throttle cable from the accelerator pedal and remove the two bolts securing the cable casing to the firewall. From inside the engine compartment, pull the cable through the firewall. For installation, reverse the removal steps, ensuring the cable casing grommet seats properly in the firewall. To adjust the cable, fully depress the accelerator pedal and check that the throttle is fully opened; if not, loosen the locknuts, depress the accelerator pedal, and adjust the cable until the throttle is fully open. Tighten the locknuts and recheck the adjustment, confirming that the throttle closes fully when the pedal is released.

Remove the two bolts securing the cable casing to the firewall.