My Garage
My Account
Cart
Genuine Toyota 4Runner Release Bearing
Clutch Release Throw Out Bearing- Select Vehicle by Model
- Select Vehicle by VIN
Select Vehicle by Model
orMake
Model
Year
Select Vehicle by VIN
For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).
6 Release Bearings found
Toyota 4Runner Clutch Release Bearing Assembly
Part Number: 31230-35110$127.87 MSRP: $181.79You Save: $53.92 (30%)Ships in 1-2 Business Days
Toyota 4Runner Clutch Release Bearing Assembly
Part Number: 31230-35070$91.20 MSRP: $128.56You Save: $37.36 (30%)Ships in 1-3 Business Days
Toyota 4Runner Clutch Release Bearing Hub
Part Number: 31231-20090$26.64 MSRP: $37.25You Save: $10.61 (29%)Ships in 1-3 Business Days
Toyota 4Runner Clutch Release Bearing Assembly
Part Number: 31230-35090$68.55 MSRP: $96.62You Save: $28.07 (30%)Ships in 1-2 Business Days
Toyota 4Runner Clutch Release Bearing
Part Number: 90363-40022$61.42 MSRP: $86.57You Save: $25.15 (30%)
Toyota 4Runner Release Bearing
The function of the Toyota 4Runner Release Bearing is to disconnect the power from the engine to the gearbox when the clutch pedal is depressed. This allows one to easily slip into gear without grinding. As the Release Bearing is inside the clutch housing, it slides over a hollow shaft and pushes against the pressure plate springs the instant you depress the clutch. This lifts the clutch disc off the flywheel and stops the flow of torque. The Release Bearing rolls back when the pedal rises and the pressure comes back. The power goes to the wheels. Throughout the generations of the trusted Toyota 4Runner, two methods have been applied to perform this motion. Early units employed a cable that pulls the clutch fork. Later versions applied a hydraulic cylinder that pushes it. However, in both layouts, the same compact bearing does the heavy lifting. The consistent contact, constant heat, and invading dust ultimately lead to degradation. The worn-out Release Bearing gives itself away by way of rattling noises, vibration of the pedal, stiff engagement, and unwilling shifts. Failure to perform the necessary service means your associated clutch components will experience additional stress. Therefore, all 4Runner owners should heed those warnings and get their service done in a timely fashion to preserve dependable driving. A factory-matched Release Bearing keeps Toyota shift feel intact.
If you are in demand for superior quality and affordable OEM Toyota 4Runner Release Bearing, then shop with us! We own a wide range of the reduced-priced genuine Toyota 4Runner Release Bearing. You can purchase in confidence as all parts come with a manufacturer's warranty. Any issues with our products? No need to worry as we have a hassle-free return policy to guide you every step of the way.
Toyota 4Runner Release Bearing Parts Questions & Experts Answers
- Q: How to Remove, Inspect, and Install the Release Bearing on a Toyota 4Runner?A:To eliminate the release cylinder, first of all, you need to delete the transmission. Thirdly, pull the release lever towards you and wrap your finger around the on the ball stud as the release lever retainer can be removed easily by pulling towards you. Pay attention to the fact that the release lever fingers are locked by the wire retainer of the bearing, then, unlock the bearing from the lever and move it off the input shaft. The release lever must be set back; furthermore, the state of boot should be check on cracks or tears; in case of worn or damaged, it should be replaced. In the lever, look at wire retainer; should it be non-existent or deformed, pull it out and dispose of it. To check, grasp the outer section of the bearing and turn the inner part with a finger applying force; if they rotate with a dragging sound or stiff feel, replace them. Do not submerge the bearing in a solvent, instead, smoothly and carefully scrub the bearing with a cloth as it would determine the condition of the bearing by visible signs of damage and wear. Again, during assembly, apply a small amount of clay like lubrication at the marked location of the clutch release lever should be lubricated while if the old retainer was removed it should be replaced with a new one. Apply high temperature grease to the groove round the release bearing and to the bearing retainer. Screw the release bearing to the release lever in the manner that it will fit well by use of the retainer clip. Using high-temperature grease put the clutch release lever ball stud through the boot, sliding the release bearing over input shaft splines, and place the lever onto the ball stud, where it should click to accommodate. Check whether the release lever comes to a free movement and check whether the release bearing moves easily on the splines of the input shaft. Dip a rag in high-temperate grease and rub it on the face of the release bearing, which comes in contact with the fingers of the pressure plate diaphragm. Last but not the least, close the procedure by performing the following removal procedure in the reverse sequence: Tighten all the bolts that connects transmission to the engine.
Related Toyota 4Runner Parts
Toyota 4Runner Clutch Fork
Toyota 4Runner Clutch Master Cylinder
Toyota 4Runner Clutch Slave Cylinder
Toyota 4Runner Pressure Plate
Toyota 4Runner Pilot Bearing
Toyota 4Runner Clutch Disc
Toyota 4Runner Clutch Slave Repair Kit
Toyota 4Runner Clutch Master Repair Kit
Toyota 4Runner Clutch Pedal
Browse by Year
2001 Release Bearing 2000 Release Bearing 1999 Release Bearing 1998 Release Bearing 1997 Release Bearing 1996 Release Bearing 1995 Release Bearing 1994 Release Bearing 1993 Release Bearing 1992 Release Bearing 1991 Release Bearing 1990 Release Bearing 1989 Release Bearing 1988 Release Bearing 1987 Release Bearing 1986 Release Bearing 1985 Release Bearing 1984 Release Bearing