Toyota 55905-89115 Knob, Heater Control

Before taking out the stereo, attach the positive electrode back to the battery. Be sure to have the stereo's protection code as needed. First remove the center front panel pieces. Then pull the control knobs free by taking off the selector knob and pulling the knobs from the rotary switches. First, unscrew the screws holding the control together, then lift the assembly slightly out from the front of the dash. When there are cables present, turn the twist flags on each control cable holder and take off the cables. Remove their electrical connectors after unplugging them. Installation is the reverse of removal. Press the engine buttons to ensure that the A/C Switch works correctly. When the cables connect to the control and the dashboard control is ready, move the cables back and forth until the controls match RECYCLE, COOL, and DEF settings. To put the air inlet damper control cable in, position the damper lever to FRESH, install the cable, and hold it stable with a clamp. Before connecting the air mix control cable, move the air mix damper to COOL position. Insert the cable and tighten the clamp while applying gentle force on the outer cable. Put the mode damper control cable in DEF mode, line up the cable end with its connection, and hold it tight with the clamp. Test the air conditioning and heater controls, then check for electrical connection problems. When a test spotlights a faulty switch, we need to replace the control modules immediately.

Unscrew the battery's negative cable, and make sure you have your stereo's anti-theft key code handy in case it has that feature. Unscrew and take out the knobs in the center cluster, and unscrew the screws found on the front of the A/C Switch. First, pull the control a bit out from its place. Then, if it has control cable mounts, rotate the flags before disconnecting the electrical connectors. Installation is the reverse of removal. Put the car in motion to make sure the A/C works as it should. As you attach the cables to their ends and fit the control panel into its place on the dash, custom-tune the cable lengths from the control setting of REcirculate, COOL, and DEFroggeR. 1) With the damper control lever in FRESH position, put on the air inlet control cable and clamp it down. To set the air mix control cable, move the air mix damper switch to COOL, insert the cable and tighten its locking clamp with a small push on the outer cable. Start by setting the mode damper control cable to DEF mode. When in DEF mode, hook the cable end to something and tighten the clamp. Test the AC and heating switches, then fix the A/C Switch if either switch breaks down during testing.

To remove the stereo in your vehicle, start by disconnecting the battery cable from the negative battery terminal, ensuring you have the correct activation code for the anti-theft system if applicable. Then, remove the center cluster trim panel and the control assembly mounting screws. Carefully pull and tilt the unit out of the dash, potentially loosening the trim pad if necessary. Check the outer sheath of the cables for indentations and mark them with paint if needed. Remove the clamps and detach the control cables, followed by unplugging the electrical connectors and lifting the control from the vehicle. To install, simply reverse the removal steps and connect or adjust the A/C Switch cables.

Unscrew the battery's negative cable, and make sure you have your stereo's anti-theft key code handy in case it has that feature. Unscrew and take out the knobs in the center cluster, and unscrew the screws found on the front of the A/C Switch. First, pull the control a bit out from its place. Then, if it has control cable mounts, rotate the flags before disconnecting the electrical connectors. Installation is the reverse of removal. Put the car in motion to make sure the A/C works as it should. As you attach the cables to their ends and fit the control panel into its place on the dash, custom-tune the cable lengths from the control setting of REcirculate, COOL, and DEFroggeR. 1) With the damper control lever in FRESH position, put on the air inlet control cable and clamp it down. To set the air mix control cable, move the air mix damper switch to COOL, insert the cable and tighten its locking clamp with a small push on the outer cable. Start by setting the mode damper control cable to DEF mode. When in DEF mode, hook the cable end to something and tighten the clamp. Test the AC and heating switches, then fix the A/C Switch if either switch breaks down during testing.

Pull the control out slightly and disconnect the cables and electrical connectors if applicable.

This is one per order

They are sold individually, so 1 piece per order