Where is the Turn Signal Flasher Located and What is its Function on a Toyota Prius?

The turn signal and hazard flasher is a single combination unit located in different areas depending on the model year, On the 2003 and the earlier models, it is available in the interior fuse/relay box at the left side of the installation board; on the 2004 through the 2009 models, it is located underneath the left side of the installation board; On the 2010 and other later models, it is located under the side defrosting air duct at the upper side of the upper installation board, whereby, this needs dismount This is true, a good flasher makes a clicking sound while in operation and if turn signals fails on one side or flasher did not click or when one bulb is flashing much faster than the other but does not light, then possibility is that the turn signal bulb is bad. If the turn signals do not blink on both sides, common reasons for such signals are a blown fuse, a faulty flasher unit, a bad switch, and a poor connection, although a blown fuse should be accompanied by a check for a short in the circuit before replacing, it. To remove the flasher, the electric connector must be disconnected and the unit taken out of the electrical center, The replacement unit should be as similar as possible to the removed unit, which can be compared before fitting it because the process involves the reverse of the above steps.

Genuine Toyota Prius Turn Signal Flasher

Turn Signal Indicator Flasher

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

3 Turn Signal Flashers found

View related parts
Toyota Prius Turn Signal Flasher Assembly
Part Number: 81980-50030
$58.89 MSRP: $82.32
You Save: $23.43 (29%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Flasher Assy, Turn Signal
- Manufacturer Note: MARK=81980-50030
- Replaced by: 81980-02030
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2011-2015 Toyota Prius | G, L, S | 4 Cyl 1.8L | 2ZRFXE; ZVW30L-AHXBBA, ZVW30L-AHXEBA, ZVW30L-AHXEBK, ZVW30L-AHXGBA
View related parts
Toyota Prius Turn Signal Flasher Assembly
Part Number: 81980-46010
$73.27 MSRP: $103.28
You Save: $30.01 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Flasher Assy, Turn Signal
- Manufacturer Note: MARK=81980-46010
- Replaced by: 81980-02050
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2004-2015 Toyota Prius | E, G, L, S | 4 Cyl 1.5L, 4 Cyl 1.8L | 1NZFXE, 2ZRFXE; NHW20L-AHEEBA, NHW20L-AHEEBK, ZVW30L-AHXBBA, ZVW30L-AHXEBA, ZVW30L-AHXEBK, ZVW30L-AHXGBA, ZVW35L-BHXBBA, ZVW35L-BHXEBA, ZVW35L-BHXEBK, ZVW35L-BHXGBA
View related parts
Toyota Prius Turn Signal Flasher Assembly
Part Number: 81980-47010
$65.60 MSRP: $92.46
You Save: $26.86 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Flasher Assy, Turn Signal; Flasher Relay, Turn Signal Flasher
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2001-2003 Toyota Prius | 4 Cyl 1.5L | 1NZFXE; NHW11L-AEEEBA, NHW11L-AEEEBK

Toyota Prius Turn Signal Flasher

Toyota Prius Turn Signal Flasher keeps the car's blinkers and hazard lamps blinking at a steady, attention grabbing rhythm so other drivers can read your intentions. Nestled in the fuse box, the Turn Signal Flasher module receives power when you nudge the stalk, then either heats a tiny bi metal strip in a classic thermal version or triggers an electronic relay in a solid state unit, each cycle powering the bulbs on and off. Early Prius models relied on the thermal style, where heat flexes spring steel to close and open the circuit while producing the familiar click. Newer Toyota hybrids favor solid state designs that use transistors and a timing chip to copy that blink and sound while handling low current LED lamps a thermal device cannot move. Both types share the same mission, yet the electronic style offers quicker response, longer life, and LED compatibility. When a Turn Signal Flasher fails, signals stop or act erratically, so matching a replacement to specific Toyota wiring and choosing an LED ready Turn Signal Flasher ensures every Prius indicator continues to flash on cue, proving this Turn Signal Flasher essential for safe travel.

If you are in demand for superior quality and affordable OEM Toyota Prius Turn Signal Flasher, then shop with us! We own a wide range of the reduced-priced genuine Toyota Prius Turn Signal Flasher. You can purchase in confidence as all parts come with a manufacturer's warranty. Any issues with our products? No need to worry as we have a hassle-free return policy to guide you every step of the way.

Toyota Prius Turn Signal Flasher Parts Questions & Experts Answers

Turn Signal Flasher Assembly
81980-46010
Q: Where is the Turn Signal Flasher Located and What is its Function on a Toyota Prius?
A:
The turn signal and hazard flasher is a single combination unit located in different areas depending on the model year, On the 2003 and the earlier models, it is available in the interior Fuse/relay box at the left side of the installation board; on the 2004 through the 2009 models, it is located underneath the left side of the installation board; On the 2010 and other later models, it is located under the side defrosting air duct at the upper side of the upper installation board, whereby, this needs dismount This is true, a good flasher makes a clicking sound while in operation and if turn signals fails on one side or flasher did not click or when one bulb is flashing much faster than the other but does not light, then possibility is that the turn signal bulb is bad. If the turn signals do not blink on both sides, common reasons for such signals are a blown fuse, a faulty flasher unit, a bad switch, and a poor connection, although a blown fuse should be accompanied by a check for a short in the circuit before replacing, it. To remove the flasher, the electric connector must be disconnected and the unit taken out of the electrical center, The replacement unit should be as similar as possible to the removed unit, which can be compared before fitting it because the process involves the reverse of the above steps.