How to remove and install Rack And Pinion on Toyota MR2?

To dismantle the steering components, first, loosen the wheel bolts, but do not take them off, use the jack to lift the car and place it on the jackstand and thereafter, take off the fronts wheels. After that, remove the steering shaft universal joint, with some reference markings made at the main shaft, joint yoke and the pinion shaft for reassembly process. Take out the two bolts from the he universal joint, and then twisting for the gear housing and the main shaft. First of all, unfasten all the connection between the tie-rod ends and the steering knuckle, then, you must unscrew the bolts of the center crossmember from both sides. Then, recall that there are four bolts that hold the rack housing bracket, and you should remove the housing assembly. For installation the axes of the column hole cover shield and the pinion shaft should be put coinciding to each other prior to tight compression of the rack housing bracket bolts while tightening them not to harm the rubber boots. Reinstall the center crossmember together with the four bolts, torque the bolts to the required specifications. Bolt the tie-rod ends to the knuckle arms with new nut-bolt and tighten and install new cotter pins. Next, the match marks placed on the steering shaft, the universal joint and the pinion shaft are aligned; the two bolts are removed and new ones are inserted and tightened. Add the front wheels and loosely screw the lug nuts, then lower the machine and reintroduce the correct lug nuts. Usually it may be suggested that the front wheels be taken for alignment by the dealer or at a specialized alignment center once the reassembly is done.

Genuine Toyota MR2 Rack And Pinion

Steering Rack And Pinion

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

12 Rack And Pinions found

View related parts
Toyota MR2 Steering Gear Assembly
Part Number: 45510-17020
Product Specifications
- Other Name: Gear Assembly, Steering
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 1985-1989 Toyota MR2 | GT, Super Charger | 4 Cyl 1.6L | 4AGELC, 4AGZE; AW11L-WCMQFA, AW11L-WCMQFK, AW11L-WCPQFA, AW11L-WCPQFK, AW11L-WJMQFA, AW11L-WJMQFK, AW11L-WJMQRA, AW11L-WJMQRK, AW11L-WJPQFA, AW11L-WJPQRA
View related parts
Toyota MR2 Power Steering Gear Assembly(For Rack & Pinion)
Part Number: 44250-17040
Product Specifications
- Other Name: Gear Assy, Power Steering(For Rack & Pinion)
- Comment: (FOR RACK & PINION)
- Replaced by: 44250-17060
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 1992-1994 Toyota MR2 | 4 Cyl 2.0L, 4 Cyl 2.2L | 3SGTE, 5SFE; SW20L-ACMZZA, SW20L-AJMZZA, SW20L-AJMZZK, SW21L-ACMZKA, SW21L-ACPZKA, SW21L-AJMZKA, SW21L-AJMZKK, SW21L-AJPZKA
View related parts
Toyota MR2 Power Steering Rack Sub-Assembly
Part Number: 44204-17020
Product Specifications
- Other Name: Rack Sub-Assembly, Power Steering; Rack
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 1990-1993 Toyota MR2 | 4 Cyl 2.0L, 4 Cyl 2.2L | 3SGTE, 5SFE; SW20L-ACMZZA, SW20L-AJMZZA, SW20L-AJMZZK, SW21L-ACMZKA, SW21L-ACPZKA, SW21L-AJMZKA, SW21L-AJMZKK, SW21L-AJPZKA
View related parts
Toyota MR2 Power Steering Rack Sub-Assembly
Part Number: 44204-17040
Product Specifications
- Other Name: Rack Sub-Assy, Power Steering; Rack
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 1992-1995 Toyota MR2 | 4 Cyl 2.0L, 4 Cyl 2.2L | 3SGTE, 5SFE; SW20L-ACMZZA, SW20L-AJMZZA, SW20L-AJMZZK, SW21L-ACMZKA, SW21L-ACPZKA, SW21L-AJMZKA, SW21L-AJMZKK, SW21L-AJPZKA
View related parts
Toyota MR2 Power Steering Gear Assembly(For Rack & Pinion)
Part Number: 44250-17020
Product Specifications
- Other Name: Gear Assy, Power Steering(For Rack & Pinion); Gear Assembly, Steering Gear
- Comment: (FOR RACK & PINION)
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 1990-1993 Toyota MR2 | 4 Cyl 2.0L, 4 Cyl 2.2L | 3SGTE, 5SFE; SW20L-ACMZZA, SW20L-AJMZZA, SW20L-AJMZZK, SW21L-ACMZKA, SW21L-ACPZKA, SW21L-AJMZKA, SW21L-AJMZKK, SW21L-AJPZKA
View related parts
Toyota MR2 Steering Gear Assembly
Part Number: 45510-17040
Product Specifications
- Other Name: Gear Assembly, Steering; Gear Assembly, Steering Gear
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 1990-1993 Toyota MR2 | 4 Cyl 2.0L, 4 Cyl 2.2L | 3SGTE, 5SFE; SW20L-ACMZZA, SW20L-AJMZZA, SW20L-AJMZZK, SW21L-ACMZKA, SW21L-ACPZKA, SW21L-AJMZKA, SW21L-AJMZKK, SW21L-AJPZKA
View related parts
Toyota MR2 Steering Rack
Part Number: 45521-17020
Product Specifications
- Other Name: Rack, Steering; Rack
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 1985-1989 Toyota MR2 | GT, Super Charger | 4 Cyl 1.6L | 4AGELC, 4AGZE; AW11L-WCMQFA, AW11L-WCMQFK, AW11L-WCPQFA, AW11L-WCPQFK, AW11L-WJMQFA, AW11L-WJMQFK, AW11L-WJMQRA, AW11L-WJMQRK, AW11L-WJPQFA, AW11L-WJPQRA
View related parts
Toyota MR2 Steering Rack
Part Number: 45521-17040
Product Specifications
- Other Name: Rack, Steering; Rack
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 1990-1993 Toyota MR2 | 4 Cyl 2.0L, 4 Cyl 2.2L | 3SGTE, 5SFE; SW20L-ACMZZA, SW20L-AJMZZA, SW20L-AJMZZK, SW21L-ACMZKA, SW21L-ACPZKA, SW21L-AJMZKA, SW21L-AJMZKK, SW21L-AJPZKA
View related parts
Toyota MR2 Steering Rack
Part Number: 45521-17100
Product Specifications
- Other Name: Rack, Steering; Rack
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 1992-1995 Toyota MR2 | 4 Cyl 2.0L, 4 Cyl 2.2L | 3SGTE, 5SFE; SW20L-ACMZZA, SW20L-AJMZZA, SW20L-AJMZZK, SW21L-ACMZKA, SW21L-ACPZKA, SW21L-AJMZKA, SW21L-AJMZKK, SW21L-AJPZKA
View related parts
Toyota MR2 Steering Gear Assembly
Part Number: 45510-17021
Product Specifications
- Other Name: Gear Assembly, Steering; Gear Assembly, Steering Gear
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 1988-1989 Toyota MR2 | GT, Super Charger | 4 Cyl 1.6L | 4AGELC, 4AGZE; AW11L-WCMQFA, AW11L-WCMQFK, AW11L-WCPQFA, AW11L-WCPQFK, AW11L-WJMQFA, AW11L-WJMQFK, AW11L-WJMQRA, AW11L-WJMQRK, AW11L-WJPQFA, AW11L-WJPQRA
View related parts
Toyota MR2 Power Steering Gear Assembly(For Rack & Pinion)
Part Number: 44250-17060
Product Specifications
- Other Name: Gear Assy, Power Steering(For Rack & Pinion); Gear Assembly, Steering Gear
- Comment: (FOR RACK & PINION)
- Replaces: 44250-17040
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 1992-1995 Toyota MR2 | 4 Cyl 2.0L, 4 Cyl 2.2L | 3SGTE, 5SFE; SW20L-ACMZZA, SW20L-AJMZZA, SW20L-AJMZZK, SW21L-ACMZKA, SW21L-ACPZKA, SW21L-AJMZKA, SW21L-AJMZKK, SW21L-AJPZKA
View related parts
Toyota MR2 Steering Gear Assembly
Part Number: 45510-17100
Product Specifications
- Other Name: Gear Assembly, Steering; Gear Assembly, Steering Gear
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 1992-1995 Toyota MR2 | 4 Cyl 2.0L, 4 Cyl 2.2L | 3SGTE, 5SFE; SW20L-ACMZZA, SW20L-AJMZZA, SW20L-AJMZZK, SW21L-ACMZKA, SW21L-ACPZKA, SW21L-AJMZKA, SW21L-AJMZKK, SW21L-AJPZKA

Toyota MR2 Rack And Pinion

If you are in demand for superior quality and affordable OEM Toyota MR2 Rack And Pinion, then shop with us! We own a wide range of the reduced-priced genuine Toyota MR2 Rack And Pinion. You can purchase in confidence as all parts come with a manufacturer's warranty. Any issues with our products? No need to worry as we have a hassle-free return policy to guide you every step of the way.

Toyota MR2 Rack And Pinion Parts Questions & Experts Answers

Steering Rack
45521-17020
Q: How to remove and install Rack And Pinion on Toyota MR2?
A:
To dismantle the steering components, first, loosen the wheel bolts, but do not take them off, use the jack to lift the car and place it on the jackstand and thereafter, take off the fronts wheels. After that, remove the steering shaft universal joint, with some reference markings made at the main shaft, joint yoke and the pinion shaft for reassembly process. Take out the two bolts from the he universal joint, and then twisting for the gear housing and the main shaft. First of all, unfasten all the connection between the tie-rod ends and the Steering Knuckle, then, you must unscrew the bolts of the center crossmember from both sides. Then, recall that there are four bolts that hold the rack housing bracket, and you should remove the housing assembly. For installation the axes of the column hole cover shield and the pinion shaft should be put coinciding to each other prior to tight compression of the rack housing bracket bolts while tightening them not to harm the rubber boots. Reinstall the center crossmember together with the four bolts, torque the bolts to the required specifications. Bolt the tie-rod ends to the knuckle arms with new nut-bolt and tighten and install new cotter pins. Next, the match marks placed on the steering shaft, the universal joint and the pinion shaft are aligned; the two bolts are removed and new ones are inserted and tightened. Add the front wheels and loosely screw the lug nuts, then lower the machine and reintroduce the correct lug nuts. Usually it may be suggested that the front wheels be taken for alignment by the dealer or at a specialized alignment center once the reassembly is done.