How to remove and install a power steering pump on 1997 through 2001 Toyota Avalon?

Disconnect the cable from the negative battery terminal. If the stereo in your vehicle is equipped with an anti-theft system, make sure you have the correct activation code before disconnecting the battery. Using a large syringe or suction gun, suck as much fluid out of the power steering fluid reservoir as possible. Place a drain pan under the vehicle to catch any fluid that spills out when the hoses are disconnected. Loosen the right front wheel lug nuts, raise the vehicle and support it securely on jackstands. Remove the right front wheel. Remove the right front fender apron seal. Loosen the clamp and disconnect the fluid return hose from the pump. Remove the pressure line-to-pump union bolt and separate the line from the pump. Remove the sealing washers on each side of the fitting - these should be replaced when installing the pump. Loosen the adjuster and pivot bolts and remove the drivebelt. Remove the pivot, adjuster and any other mounting bolts, and remove the pump. Installation is the reverse of removal. Be sure to tighten the fluid line banjo bolt and the adjuster and pivot bolts to the torque. Adjust the drivebelt tension. Top up the fluid level in the reservoir and bleed the system.

How to remove and install the power steering pump on 2003 through 2009 Toyota 4Runner?

Remove the power steering fluid from the reservoir. If working on a VB model, remove the air filter housing. Remove the drivebelt. Disconnect the two vacuum hoses, if equipped, or the electrical connector at the power steering fluid pressure sensor. Position a drain pan under the power steering pump, then disconnect the pressure and feed hoses from the backside of the pump, plugging the hoses to prevent contaminants from entering and discarding the sealing washer(s). Remove the pump mounting fasteners and lift the pump from the engine compartment, taking care not to spill fluid on the painted surfaces. Installation is the reverse of removal, using new sealing washers on both sides of the pressure line fitting and tightening the pressure line banjo bolt and the pump mounting fasteners to the specified torque values. Fill the power steering reservoir with the recommended fluid and bleed the system.

Genuine Toyota Power Steering Pump

Power Steering Pump Unit

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

225 Power Steering Pumps found

View related parts
Toyota Pump Assy, Vane
Part Number: 44320-60182
$306.34 MSRP: $439.27
You Save: $132.93 (31%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Power Steering Pump, Pulley Adjust Bracket
- Replaces: 44320-60181
Fits the following Toyota Models:
- Land Cruiser | 1992-1997 | 6 Cyl 4.0L, 6 Cyl 4.5L
View related parts
Toyota Pump Assy, Vane
Part Number: 44320-60310
$307.39 MSRP: $440.77
You Save: $133.38 (31%)
Ships in 1 Business Day
ADD TO CART
Product Specifications
- Other Name: Power Steering Pump
Fits the following Toyota Models:
- Land Cruiser | 1998-2003 | 8 Cyl 4.7L
View related parts
Toyota Pump Assembly, VANE
Part Number: 44310-0C090
$276.76 MSRP: $396.87
You Save: $120.11 (31%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Pump Assy, Vane; Power Steering Pump
Fits the following Toyota Models:
- Tundra | 2007-2021 | Limited, Platinum, SR5 | 6 Cyl 4.0L, 8 Cyl 4.6L, 8 Cyl 4.7L, 8 Cyl 5.7L
View related parts
Toyota Pump Assy, Vane
Part Number: 44320-35490
$345.90 MSRP: $495.99
You Save: $150.09 (31%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Power Steering Pump
Fits the following Toyota Models:
- 4Runner | 1996-2002 | LULI, SR5B, SR5V | 4 Cyl 2.7L, 6 Cyl 3.4L
View related parts
Toyota Pump Assy, Vane
Part Number: 44320-04052
$337.43 MSRP: $483.85
You Save: $146.42 (31%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Power Steering Pump
- Replaces: 44320-04051
Fits the following Toyota Models:
- Tacoma | 1996-2004 | DLX, SR5 | 4 Cyl 2.4L, 4 Cyl 2.7L, 6 Cyl 3.4L
View related parts
Toyota Pump Assy, Vane
Part Number: 44320-35610
$285.93 MSRP: $410.00
You Save: $124.07 (31%)
ADD TO CART
Product Specifications
- Other Name: Power Steering Pump
Fits the following Toyota Models:
- 4Runner | 2003-2009 | Limited, SR5 | 6 Cyl 4.0L, 8 Cyl 4.7L
View related parts
Toyota Pump Assembly, VANE
Part Number: 44310-35660
$339.55 MSRP: $499.82
You Save: $160.27 (33%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Pump Assy, Vane; Power Steering Pump
- Replaces: 44310-35650
Fits the following Toyota Models:
- 4Runner | 2003-2009 | Limited, SR5 | 6 Cyl 4.0L, 8 Cyl 4.7L
- FJ Cruiser | 2007-2010 | 6 Cyl 4.0L
View related parts
Toyota Pump Assy, Vane
Part Number: 44320-14250
$308.90 MSRP: $442.94
You Save: $134.04 (31%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Power Steering Pump
Fits the following Toyota Models:
- Supra | 1993-1998 | 6 Cyl 3.0L
View related parts
Toyota Pump Assembly, VANE
Part Number: 44310-04150
$307.74 MSRP: $441.27
You Save: $133.53 (31%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Pump Assy, Vane; Power Steering Pump
Fits the following Toyota Models:
- Tacoma | 2005-2016 | Base, Limited, SR5 | 4 Cyl 2.7L, 6 Cyl 3.5L, 6 Cyl 4.0L
View related parts
Toyota Pump Assy, Vane
Part Number: 44320-60090
$333.60 MSRP: $478.37
You Save: $144.77 (31%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Power Steering Pump
Fits the following Toyota Models:
- Land Cruiser | 1988-1990 | 6 Cyl 4.0L
View related parts
Toyota Pump Assembly, VANE
Part Number: 44310-0C110
$282.33 MSRP: $404.84
You Save: $122.51 (31%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Pump Assy, Vane; Power Steering Pump
Fits the following Toyota Models:
- Sequoia | 2008-2022 | Limited, Platinum, SR5 | 8 Cyl 4.6L, 8 Cyl 4.7L, 8 Cyl 5.7L
- Tundra | 2009-2014 | Limited, Platinum, SR5 | 6 Cyl 4.0L, 8 Cyl 4.6L, 8 Cyl 4.7L, 8 Cyl 5.7L
View related parts
Toyota Pump Assembly, VANE
Part Number: 44310-07040
$316.20 MSRP: $453.41
You Save: $137.21 (31%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Pump Assy, Vane; Power Steering Pump
Fits the following Toyota Models:
- Avalon | 2005-2012 | Limited, XL, XLS | 6 Cyl 3.5L
- Camry | 2007-2011 | LE, SE, XLE | 4 Cyl 2.4L, 4 Cyl 2.5L, 6 Cyl 3.5L
View related parts
Toyota Pump Assembly, VANE
Part Number: 44310-04200
$296.14 MSRP: $424.64
You Save: $128.50 (31%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Pump Assy, Vane; Power Steering Pump
Fits the following Toyota Models:
- Tacoma | 2015-2023 | Base, Limited, SR5 | 4 Cyl 2.7L, 6 Cyl 3.5L, 6 Cyl 4.0L
View related parts
Toyota Pump Assembly, VANE
Part Number: 44310-35750
$285.12 MSRP: $408.83
You Save: $123.71 (31%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Pump Assy, Vane; Power Steering Pump
Fits the following Toyota Models:
- FJ Cruiser | 2009-2014 | 6 Cyl 4.0L
View related parts
Toyota Pump Assembly, VANE
Part Number: 44310-0C040
$382.83 MSRP: $563.53
You Save: $180.70 (33%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Pump Assy, Vane; Power Steering Pump
Fits the following Toyota Models:
- Tundra | 2003-2006 | DLX, Limited, SR5 | 6 Cyl 3.4L, 6 Cyl 4.0L, 8 Cyl 4.7L
View related parts
Toyota Pump Assy, Vane
Part Number: 44320-48040
$306.34 MSRP: $439.27
You Save: $132.93 (31%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Power Steering Pump
Fits the following Toyota Models:
- Highlander | 2003-2007 | 4 Cyl 2.4L, 6 Cyl 3.0L, 6 Cyl 3.3L
View related parts
Toyota Pump Assembly, VANE
Part Number: 44310-33170
$306.11 MSRP: $438.94
You Save: $132.83 (31%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Pump Assy, Vane; Power Steering Pump
Fits the following Toyota Models:
- Camry | 2007-2011 | LE, XLE | 4 Cyl 2.4L, 4 Cyl 2.5L, 6 Cyl 3.5L
View related parts
Toyota Pump Assy, Vane
Part Number: 44320-60181
$306.34 MSRP: $439.27
You Save: $132.93 (31%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Replaced by: 44320-60182
Fits the following Toyota Models:
- Land Cruiser | 1992-1996 | 6 Cyl 4.0L, 6 Cyl 4.5L
View related parts
Toyota Pump Assembly, VANE
Part Number: 44310-17011
$344.41 MSRP: $506.97
You Save: $162.56 (33%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Pump Assy, Vane; Power Steering Pump
- Replaces: 44310-17010
Fits the following Toyota Models:
- MR2 | 1990-1995 | 4 Cyl 2.0L, 4 Cyl 2.2L
View related parts
Toyota Pump Assembly, VANE
Part Number: 44310-06071
$313.88 MSRP: $450.08
You Save: $136.20 (31%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Pump Assy, Vane; Power Steering Pump
- Manufacturer Note: (L)
- Replaces: 44310-06070, 44310-33150
Fits the following Toyota Models:
- Camry | 2002-2010 | LE, SE, XLE | 4 Cyl 2.4L, 4 Cyl 2.5L, 6 Cyl 3.0L, 6 Cyl 3.3L, 6 Cyl 3.5L
- Solara | 2001-2008 | SE, SLE | 4 Cyl 2.2L, 4 Cyl 2.4L, 6 Cyl 3.0L, 6 Cyl 3.3L

| Page 1 of 12 |Next >

1-20 of 225 Results

About Toyota Power Steering Pump

In the steering system, the power steering pump makes it easier for you to turn your Toyota car. When you are running your car and turning the wheel, the power steering pump sends fluid to the steering gear. Here are some signs showing that there is a possibility your power steering pump is worn: difficulty on turning he steering wheel; leak of power steering fluid; a groaning-like noise. If any one of them happens on your Toyota car, do not wait to get a new power steering pump. For your convenient, we offer all Toyota OEM power steering pump. Replacing some equipment in your Toyota car is inevitable over the time. Fortunately, you can easily find any Toyota body parts you need online here and we promise to offer low price, high quality and quick delivery.

Toyota Power Steering Pump Parts Questions & Experts Answers

Pump Assy, Vane
44320-07011
Q: How to remove and install a power steering pump on 1997 through 2001 Toyota Avalon?
A:
Disconnect the cable from the negative battery terminal. If the stereo in your vehicle is equipped with an anti-theft system, make sure you have the correct activation code before disconnecting the battery. Using a large syringe or suction gun, suck as much fluid out of the power steering fluid reservoir as possible. Place a drain pan under the vehicle to catch any fluid that spills out when the hoses are disconnected. Loosen the right front wheel lug nuts, raise the vehicle and support it securely on jackstands. Remove the right front wheel. Remove the right front fender apron seal. Loosen the clamp and disconnect the fluid return hose from the pump. Remove the pressure line-to-pump union bolt and separate the line from the pump. Remove the sealing washers on each side of the fitting - these should be replaced when installing the pump. Loosen the adjuster and pivot bolts and remove the drivebelt. Remove the pivot, adjuster and any other mounting bolts, and remove the pump. Installation is the reverse of removal. Be sure to tighten the fluid line banjo bolt and the adjuster and pivot bolts to the torque. Adjust the drivebelt tension. Top up the fluid level in the reservoir and bleed the system.
Pump Assy, Vane
44320-35610
Q: How to remove and install the power steering pump on 2003 through 2009 Toyota 4Runner?
A:
Remove the power steering fluid from the reservoir. If working on a VB model, remove the air filter housing. Remove the drivebelt. Disconnect the two vacuum hoses, if equipped, or the electrical connector at the power steering fluid pressure sensor. Position a drain pan under the power steering pump, then disconnect the pressure and feed hoses from the backside of the pump, plugging the hoses to prevent contaminants from entering and discarding the sealing washer(s). Remove the pump mounting fasteners and lift the pump from the engine compartment, taking care not to spill fluid on the painted surfaces. Installation is the reverse of removal, using new sealing washers on both sides of the pressure line fitting and tightening the pressure line banjo bolt and the pump mounting fasteners to the specified torque values. Fill the power steering reservoir with the recommended fluid and bleed the system.